Relife RL-428-OR Flux Paste Japan Rosin 100G
₨ 2,500
Relife RL-428-OR BGA Flux Paste, 100g Japanese Rosin
Relife RL-428-OR is a light yellow, high-viscosity rosin flux paste in a 100g jar. It uses imported Japanese rosin and a halogen-free, high-activity formula. You use it for BGA reballing, CPU and IC rework, and general PCB soldering on mobile phone motherboards. High insulation resistance protects dense boards, and the paste stays in place under hot air so your joints wet cleanly. The large jar covers daily bench volume for shops that empty small syringes within days. Mechanicpk supplies this flux to Pakistani technicians who want consistent reballing results at shop scale.
In stock
Relife RL-428-OR BGA Flux Paste for Mobile Repair, 100g Jar
Relife RL-428-OR is a BGA flux paste for mobile repair benches that need volume instead of 10 ml syringes. The 100g jar holds a light yellow, high-viscosity rosin paste made with imported Japanese rosin. The formula runs halogen-free with high activity and high insulation resistance. Mechanicpk lists it for shops that reball, rework, and re-tin boards every day. You get consistent wetting on pads, solder balls, and component leads, and the paste body stays where you place it under hot air.
Japanese Rosin Base and Halogen-Free Activity
The rosin base sets this flux apart from thin, runny gels. Imported Japanese rosin gives the paste its viscosity and tinning behavior, so it clings to pads and holds a stencil pattern during reballing. High activity strips surface oxide from copper pads and solder spheres. Tin then flows into bright, solid joints instead of grainy ones. The halogen-free formulation also limits the corrosive residue risk on fine-pitch boards. You will notice the difference on oxidized pads from water-damaged boards, where weak flux leaves cold joints and sends the phone back to your bench. Relife describes the paste as a light yellow, impurity-free formulation, and that clean colour helps you judge flow under the microscope. Keep the jar capped between jobs, because rosin pastes thicken when they sit open under bench heat.
Reballing, BGA Rework, and PCB Soldering Workflow
Apply a thin film across the cleaned pads before you place the stencil. Then spread a controlled layer over the new spheres before reflow. The same reballing flux paste also helps during removal: brush it around the IC edges, heat with your hot air station, and lift the chip once the joints flow. After reballing, add a thin coat again when you seat the chip, so the balls collapse evenly on the pads. This one paste covers CPU, eMMC, power IC, and charging IC jobs on mobile phone motherboards. It also handles general PCB soldering when you tin wires or rebuild broken traces. Dead phone, charging issue, and hang on logo faults that trace back to weak BGA joints all pass through this step. Pair the paste with a stable hot air station and a PCB holder, so your heat stays controlled across the whole chip.
High Insulation Resistance for Dense Mobile Boards
Dense mobile boards punish conductive residue. Relife formulates RL-428-OR with high insulation resistance, so leftover flux is less likely to create leakage paths between fine-pitch pads near the CPU and power management areas. The formula aims for minimal residue, but you should still wipe the board with isopropyl alcohol and check under your microscope before you close the phone. That inspection habit catches missed bridges and prevents repeat visits after a hardware fault returns. The 100g jar also suits daily shop volume. You scoop what you need with a brush or spatula and avoid the waste that comes from squeezing half-dried syringes. For a technician who changes ICs all week, one jar sits on the bench as a standing consumable, next to your reballing kit and solder wick.
| Weight | 0.11 kg |
|---|
Key Features
- ✓100g jar for high-volume shop use
- ✓Imported Japanese rosin base
- ✓Light yellow, impurity-free paste
- ✓Halogen-free formulation
- ✓High activity for oxide removal and clean tin flow
- ✓High viscosity that holds position under hot air
- ✓High insulation resistance for dense boards
- ✓Easy to apply with a brush or spatula
Specifications
| Brand | Relife |
|---|---|
| Model | RL-428-OR |
| Category | Soldering Flux Paste (BGA / PCB) |
| Compatibility | Universal, not device-specific |
| Supported Devices | Mobile phone motherboards, CPU and BGA components, PCB assemblies |
| Technology | Rosin-based, halogen-free, high-activity flux paste |
| Material | Imported Japanese rosin |
| Dimensions | 53mm x 53mm (jar) |
| Weight | 100g (net) |
Common Repair Uses
- ✓BGA reballing of CPU and IC packages
- ✓IC change karna on mobile motherboards
- ✓Dead phone repair after BGA joint failure
- ✓Charging issue repair with charging IC reflow
- ✓Hang on logo faults caused by weak CPU or eMMC joints
- ✓Pad re-tinning before chip placement
- ✓General PCB soldering and trace repair
- ✓Wire tinning and jumper lagana on fine pads
Compatible Devices
- ✓Universal scope. The paste works on component types, not specific phone models.
- ✓Mobile phone motherboards (all brands)
- ✓CPU and SoC BGA packages
- ✓eMMC BGA chips
- ✓Power management ICs (PMIC)
- ✓Charging ICs
- ✓SMD components on mobile PCBs
- ✓Computer and laptop PCB components
- ✓General electronic PCB assemblies
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is Relife RL-428-OR flux paste halogen-free and does it need cleaning?
Can I use Relife RL-428-OR for BGA reballing on mobile phone CPU chips?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



