RELIFE RL-056B 2-in-1 OCA Glue Remover & Cutter
₨ 1
RELIFE RL-056B Glue Remover for OCA, LOCA and Hard Plastic Residue
The RELIFE RL-056B combines a motorized glue removal head with a built-in cutting function in one handheld tool. It lifts OCA, LOCA, and hard plastic residue from OLED and LCD screen assemblies. The adjustable 3 to 12V range lets you match head speed to the adhesive in front of you. A stainless steel blade, precision steel bearings, and an ergonomic handle support steady work through long screen refurbishment sessions. For technicians who separate displays daily, this tool keeps residue removal and cutting on one bench station.
Out of stock
RELIFE RL-056B Glue Remover for Clean OLED Screen Disassembly
The RELIFE RL-056B glue remover is a motorized handheld tool that handles two jobs on the same bench station. Its glue removal function lifts OCA, LOCA, and hard plastic residue from OLED and LCD screen assemblies. Its built-in cutting function separates bonded layers with precision adjustment. You get one tool for adhesive removal and controlled cutting, so you spend less time swapping attachments during a screen refurbishment. The sections below explain how the motor, the cutting function, and each residue type fit into your repair workflow.
Motor Speed and the 3 to 12V Adjustment
The RL-056B offers an adjustable transmission range from 3 to 12V. This range lets you set the head speed to match the adhesive in front of you. Lower settings give slower, more controlled movement when you work close to the display edge or near a flex cable path. Higher settings move faster through thicker OCA layers and heavier LOCA residue, which cuts the time per screen on a busy bench. You find the right setting by testing on a scrap area first, then increasing until the head clears the adhesive without dragging. The high-power motor holds steady speed under load, so your pass stays even along a full screen edge. Precision steel bearings reduce wobble, which helps the head track straight along the frame instead of skipping across it. Keep the setting consistent for each screen type so your results repeat from one job to the next.
Built-in Cutting Function and Blade Care
The cutting function is the second job this tool handles. It includes precision adjustment, so you can set the cut to suit a narrow frame seam or a wider adhesive band. Use the cutting function once the adhesive has softened and the screen needs separating from the housing. The stainless steel blade provides durability across repeated cuts, but it still needs attention. Adhesive buildup on the edge dulls the cut and drags the screen, so clean the blade after each session. Make slow, steady passes rather than fast pushes, since a rushed cut tends to chip the panel edge or tear the flex. Store the tool with the blade protected from knocks, because a bent edge changes the angle you rely on for clean separation. Treat the cutting edge with the same respect you give a sharp hobby knife, and keep your fingers clear of the cutting path.
Removing OCA, LOCA and Hard Plastic Residue
OCA is the optically clear adhesive that bonds the touch layer to the display stack. LOCA is a liquid optically clear adhesive that fills gaps in certain assemblies, which makes it harder to lift in one piece. Hard plastic residue comes from original frame adhesive and plastic bonding points left on the housing. Each residue type needs a different approach on your bench. OCA usually comes off in a few broad passes once you start at the corner and work along the edge. LOCA takes more passes because it sits in thicker, uneven beads and leaves small remnants behind. Hard plastic residue lifts best when you keep the head moving and avoid holding it in one spot, since a stationary tip can scratch the surface. After each pass, check the glass or frame under good light before you move on. Remove the remaining film with a clean cloth and a suitable cleaning solvent, so the next adhesive layer bonds properly.
Fitting the RL-056B Into Your Repair Bench Workflow
This tool belongs in the display refurbishment stage, after the screen is opened and before the new adhesive is applied. Clear the old residue completely, because leftover film weakens the bond of the replacement layer. Pair the RL-056B with a heat source for softening stubborn adhesive, a plastic pry tool for lifting the panel, and a cleaning step with isopropyl alcohol. If your daily volume is high, the consistent motor speed saves time per screen and reduces variation between jobs. Batch similar screens together so you keep one speed setting through the session and avoid constant recalibration. For occasional work on small adhesive spots, a manual scraper may do the job, but it cannot match the speed of a motorized head across full screen edges. Your next upgrade step is a Hot Air Station for controlled softening of stubborn adhesive. The RL-056B suits any bench where you refurbish OLED and LCD screens regularly and need one tool for both residue removal and cutting.
| Weight | 0.10 kg |
|---|
Key Features
- ✓Removes OCA, LOCA, and hard plastic residue from OLED and LCD assemblies
- ✓Built-in cutting function with precision adjustment
- ✓Adjustable voltage range from 3 to 12V
- ✓High-power motor for steady speed under load
- ✓Precision steel bearings for smooth, low-wobble movement
- ✓Stainless steel blade for durable cutting
- ✓Ergonomic handle for control during long sessions
- ✓Single tool for residue removal and screen separation
Specifications
| Brand | RELIFE |
|---|---|
| Model | RL-056B |
| Category | Glue Removers and Cutters |
| Compatibility | Universal, not device-specific |
| Technology | Motorized with built-in cutting function |
| Material | Stainless steel blade |
| Output Voltage | 3 to 12V adjustable |
Common Repair Uses
- ✓OCA removal during OLED screen refurbishment
- ✓LOCA residue clearing on display assemblies
- ✓Hard plastic residue removal from frames before reassembly
- ✓Separating display glass from the housing once adhesive has softened
- ✓Cutting adhesive along narrow frame seams
- ✓Cleaning old adhesive before applying new OCA
- ✓Tablet screen refurbishment on adhesive-bonded panels
- ✓Electronics residue cleanup on compatible repair surfaces
Compatible Devices
- ✓Universal, not device-specific. Scope covers OLED and LCD screen assemblies on mobile phones and tablets.
- ✓Universal, not device-specific: any OLED or LCD assembly that needs adhesive removal
- ✓OLED screen assemblies with OCA or LOCA residue
- ✓LCD screen assemblies during separation and residue removal
- ✓Mobile phone screen assemblies
- ✓Tablet screen assemblies
- ✓Hard plastic frame residue on mobile housings
- ✓Glass-to-frame adhesive bonding points
- ✓Glue residue on compatible electronics surfaces
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What voltage range does the RL-056B support?
Can the RL-056B remove LOCA from OLED screens?
Related products
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



