Relife RL-2030 Desoldering Wick 2mm x 3m Copper Braid
₨ 1
Relife RL-2030 Desoldering Wick, 2mm x 3m
The Relife RL-2030 desoldering wick gives your bench a 3-metre spool of 2.0mm pure copper braid for lifting excess solder off PCB pads. You press the braid on the joint, heat it with your iron, and the braid pulls molten solder away, so IC pads, connector pins and BGA lands come out clean for the next step. The oxidation-resistant copper braid keeps its absorption through repeated use, and the low-residue finish leaves the board clear for reballing or resoldering. Technicians in mobile repair shops use it daily for pad cleaning after IC removal, charging port work and board-level fault repair. Mechanicpk supplies the Relife RL-2030 across Pakistan.
Out of stock
Relife RL-2030 Desoldering Wick for Clean, Precise Pad Work
The Relife RL-2030 desoldering wick is a 2.0mm wide, 3-metre pure copper braid built for solder removal on phone motherboards and general PCBs. Distributor documentation confirms the copper construction, the 2.0mm width and the 3m spool length. The braid works by capillary action: molten solder flows into the woven copper, and the pad underneath comes out flat and ready for the next stage of your repair.
Why 2.0mm Width Suits Phone Board Work
A 2mm braid sits in the middle of the width range that mobile technicians reach for. It covers the pad area of most SMD components and board-to-board connectors without bridging into neighbouring pads. When you finish an IC change karna job, the leftover solder on the lands forms uneven peaks. This wick flattens them in a few passes, so the replacement chip seats evenly. For wider BGA lands or heavy ground planes, you step up to a wider braid. For tight rows of fine pads, you step down. The 2.0mm width handles the everyday work between those two extremes.
Copper Braid Construction and Heat Response
Pure copper conducts heat quickly, so the braid reaches solder melting temperature fast and pulls solder in before it re-freezes on the pad. The oxidation-resistant finish keeps the copper bright and absorbent from the first centimetre to the last. Low residue means you spend less time scrubbing flux and tin leftovers off the board afterward. You trim the used section with cutters and feed fresh braid onto the joint, which keeps every pass absorbing at full capacity.
Where It Fits in Your Repair Workflow
The wick sits right after component removal on the PCB repair bench. You lift a damaged IC with your hot air station, then clean the pads with the braid and your soldering iron, then inspect under the microscope. A clean pad lets you tin it fresh or fit a reballed chip. This sequence applies to a charging issue traced to a faulty charging IC, a dead phone with a shorted power rail, a display problem from a damaged connector, or a hardware fault where you need to remove a bridge between pins. Pair the braid with a good soldering station, a PCB holder to steady the board, and a multimeter to confirm the short is gone before you power up.
Technical Buyers Choose It for Predictable Consumption
A 3m spool gives a repair shop roughly a full month of regular pad cleaning on a busy bench, and the compact spool fits in a tool drawer or a toolbox tray. Shop owners who stock several widths use the RL-2030 as the standard general-purpose size and keep narrower and wider braids for specialist jobs. Mechanicpk stocks Relife desoldering wick in the sizes technicians ask for, so you can build a complete set of braid widths from one supplier in Pakistan.
| Weight | 0.1 kg |
|---|
Key Features
- ✓2.0mm braid width suited to general SMD and connector pads
- ✓3-metre spool length for repeated use
- ✓Pure copper construction for fast heat conduction
- ✓Oxidation-resistant copper for stable absorption
- ✓Low residue finish after solder removal
- ✓Suitable for all kinds of PCB circuit boards
- ✓Capillary action braid pulls molten solder off pads
- ✓Compact spool fits any repair bench or toolbox
Specifications
| Brand | Relife |
|---|---|
| Model | RL-2030 |
| Category | Desoldering Wick / Soldering Consumables |
| Compatibility | Universal (all kinds of PCB circuit boards) |
| Material | Pure copper |
| Dimensions | 2.0mm width x 3m length |
Common Repair Uses
- ✓Solder removal and pad cleaning on PCBs
- ✓Cleaning pads after IC removal
- ✓Flattening BGA lands before reballing
- ✓Removing solder bridges between pins
- ✓Charging port and connector pad cleanup
- ✓Removing excess solder after component replacement
- ✓Prepping pads for fresh tinning
- ✓Cleaning pads after chip-off work
- ✓Correcting soldering mistakes on small boards
Compatible Devices
- ✓Universal — not device-specific; works on any PCB, including smartphone, tablet and general electronics motherboards
- ✓Smartphone motherboards (Android and iPhone boards)
- ✓Tablet motherboards
- ✓BGA pads on phone PCBs
- ✓SMD component pads
- ✓IC chip pads after chip removal
- ✓Board-to-board connector pads
- ✓Charging port solder pads
- ✓General electronics PCBs
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What width and length is the Relife RL-2030 desoldering wick?
Can the Relife RL-2030 clean BGA pads on phone motherboards?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock



