Back to products
Kada Original 2018d+Curved Nozzle (3Pcs)
Kada 2018D+ Curved Nozzle Set (3Pcs) Original Original price was: ₨ 2,000.Current price is: ₨ 1,500.

YCS T-01 Heat Insulating Silicone Repair Pad

₨ 1,300

YCS T-01 Silicone Repair Pad

The YCS T-01 heat insulating silicone repair pad gives your bench a protected, stable surface for mobile phone and PCB work. You place the board on the pad before IC change karna, reballing, flux cleaning or jumper lagana, and the silicone layer separates the heat zone from your table. The pad suits hot air station and soldering station setups, and it keeps screws, shields and small components from sliding around while you work. Technicians in repair shops and service centers across Pakistan use a dedicated silicone pad to keep the bench clean, organized and safer under rework heat. Mechanicpk supplies the YCS T-01 as a dependable bench foundation for daily hardware fault repair.

In stock

18 People watching this product now!
Description

Heat Insulating Silicone Repair Pad for a Safer Rework Bench

The YCS T-01 is a heat insulating silicone repair pad built for the surface where your repair actually happens. Every hot air pass, soldering iron contact and flux spill lands on your bench first, so the pad takes that load instead of your table. Mechanicpk stocks the YCS T-01 for technicians who treat the work surface as part of the toolset, not an afterthought.

Where the Pad Sits in a Rework Workflow

A silicone pad anchors the first and last steps of board-level repair. You lay the motherboard on it for inspection, then keep it there for IC removal, pad cleaning, reballing and reflow. The silicone body isolates the heated area from your table, which matters when a dead phone needs long, repeated heat cycles on the same spot. Pair it with a hot air station, a soldering station and a PCB holder, and the full rework chain stays on one controlled surface.

Silicone Surface Advantages for Board-Level Work

Silicone gives you a non-metallic, flexible work surface that suits PCB handling. A board resting on it stays put while you apply flux or position a stencil, and the pad lets you wipe off flux residue and solder splatter after the job. You also get a defined zone for sorting screws, shield cans and flex connectors, so a boot loop or charging issue repair does not end with missing parts. Keep a clean pad under a microscope setup too, because a stable, tidy surface reduces slips during fine soldering.

Compatibility Scope for Your Bench

The YCS T-01 works as a universal bench accessory, so it does not depend on a phone model, chipset or brand. Place Android boards, iPhone logic boards, tablet boards and laptop sub-boards on it the same way. That universal scope makes it a practical add-on next to ISP pinout tools, eMMC programmers, UFS adapters and test boxes, because those tools all need a safe, organized surface around the board.

Why Technicians Choose a Dedicated Repair Pad

A bare wooden or laminate table marks quickly under rework heat and collects flux and solder residue. A dedicated pad protects the table and gives you a consistent surface from one repair to the next. Technicians who handle display problems, network issues, hang on logo faults and charging port repairs in the same shift benefit from a surface that wipes clean between jobs. For shops that scale their daily repair volume, a pad on every bench keeps workstations uniform and easy to reset.

Buying Guidance for Pakistan Repair Shops

Mechanicpk supplies the YCS T-01 to repair shops, service centers and training institutes that equip multiple benches. If you are building a complete rework station, add reballing kits, multimeters and PCB holders from the same catalog so your bench ships ready to use. You can also move up from a basic pad to a larger bench setup as your workload grows.

Additional information
Weight0.9 kg
Q & A
Please login to post questions

Key Features

  • Heat insulating silicone body that separates the work zone from your table
  • Flat, stable surface for PCB and motherboard handling
  • Suits hot air station and soldering station setups
  • Wipes clean after flux and solder splatter
  • Universal use across phone, tablet and laptop boards
  • Gives you a defined area for screws and small parts
  • Protects the bench surface during repeated heat cycles
  • Fits rework benches, microscope setups and training stations

Specifications

BrandYCS
ModelT-01
CategoryRepair Pad / Heat Insulating Mat
CompatibilityUniversal bench accessory, not device-specific
MaterialSilicone
TechnologyHeat insulating silicone work surface

Common Repair Uses

  • Bench surface for heat-based and general board-level repair
  • Hot air station rework on phone boards
  • Soldering iron work on connectors and components
  • IC change karna and component replacement
  • BGA reballing and pad cleaning
  • Flux cleaning and board washing prep
  • Charging port and connector repair
  • Microscope-assisted board inspection
  • Sorting screws and small parts during phone disassembly

Compatible Devices

  • Universal bench pad, usable under any board you repair (not tied to a specific model or chipset)
  • Android smartphone motherboards
  • iPhone logic boards
  • Tablet motherboards
  • Laptop and MacBook sub-boards
  • Small PCB modules and daughter boards
  • Charging port and flex sub-boards
  • Display and battery connector boards
  • Loose screws, shield cans and small parts during disassembly

FAQ

What is the product name?
The product name is YCS T-01 Heat-insulating Silicone Table Repair Pad.
What is the brand of this product?
The brand of this product is YCS.
What is the model of this product?
The model of this product is T-01.
What is this product used for?
This product is used as a heat insulating silicone bench surface for mobile phone, tablet and PCB repair, including soldering, hot air rework and reballing.
Which devices are compatible with this product?
This product is a universal bench accessory, so it works with any phone, tablet or laptop board you place on it.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Can I use this silicone pad under a hot air station for IC change karna?
Yes. The pad is a heat insulating work surface for rework benches, so you can place the board on it during hot air work and IC replacement. Keep the hot air nozzle on the component, not on the pad, to avoid unnecessary direct heat on the silicone.
Is the YCS T-01 pad device-specific or can I use it for all phone boards?
It is a universal bench pad. It does not depend on brand, chipset or model, so you can use it for Samsung, Oppo, Vivo, Infinix, Tecno and iPhone boards alike.