2UUL PB01 PadBall Solder Balls for iPhone Pad Rework
₨ 1,900
iPhone Pad Rework Solder Balls
The 2UUL PB01 PadBall Solder Balls deliver 100,000 uniform Sn63/Pb37 spheres in one bottle, built for solder pad rework on iPhone motherboards. The eutectic alloy melts at 183°C, so each ball reflows in one clean step under a hot air station and rebuilds a missing or lifted pad at a consistent height. Technicians reach for these solder balls for iPhone pad rework when a dead phone, charging issue, or hardware fault traces back to a damaged contact point. Mechanicpk stocks the PB01 variant for repair shops and service centers across Pakistan that need precise, repeatable pad restoration under the microscope.
In stock
2UUL PB01 PadBall Solder Balls: Technical Overview for iPhone Pad Rework
The 2UUL PB01 PadBall Solder Balls give your iPhone repair bench a ready supply of uniform eutectic spheres for pad rework. Each bottle holds 100,000 balls of Sn63/Pb37 alloy, so these solder balls for iPhone pad rework keep a busy workshop stocked for a large number of repairs. When a dead phone or charging issue traces back to a lifted or missing pad on the logic board, you rebuild the contact point with a single ball instead of dragging solder across the pad and guessing the height. Mechanicpk supplies the PB01 variant, which 2UUL builds specifically for iPhone motherboards.
Sn63/Pb37 Alloy: Why the Eutectic Mix Matters
Sn63/Pb37 is a eutectic composition, so the alloy melts at one fixed temperature instead of across a softening range. The PB01 lists a melting point of 183°C. That single transition lets each ball flip from solid to liquid in one step under your hot air station, wet the pad, and settle into a smooth dome without a pasty stage that leaves lumpy joints. Uniform ball size gives you repeatable height from pad to pad on the same board. Distributor documentation also describes a low-oxidation composition with minimal residue, which lowers the risk of bridging between neighboring pads on a dense iPhone board. The alloy contains lead, so run fume extraction at your bench and wash your hands after you handle the bottle.
Where PB01 Fits in a Pad Rework Workflow
Pad rework starts after the failed component or chip comes off the board. You clean the damaged area with your soldering station and desoldering wick, apply flux, and place a ball on the bare pad. A short pass with the hot air station reflows the ball into a raised contact point. A check under your microscope confirms height and position before the replacement part goes back on. This sequence fixes the hardware fault at the pad itself, so the new IC or chip sits on a solid joint instead of a repeat failure. Boards that arrive after a drop often show lifted pads beside the removed component, and PB01 gives you a fast way to restore each one. The same approach applies to pads under BGA and CSP packages, and distributor notes list CPU, GPU, and chipset reballing among the applications. A PCB holder keeps the board steady while you place balls, which matters when each sphere measures a fraction of a millimeter. After reflow, a multimeter continuity check from the rebuilt pad to its trace confirms the repair before you close the phone.
PB01 or PB02: Picking the Right 2UUL Bottle
2UUL splits the PadBall range into two codes. PB01 targets iPhone solder pad rework, and PB02 targets Android. Check the code before you order, because the two bottles carry different net weights: 5.5 g for the PB01 and 7.2 g for the PB02. The PB01 bottle measures 16 mm by 16 mm by 32 mm, so it fits beside the microscope or in a bench drawer without taking space. Shops building a complete reballing setup pair PadBall with Reballing Kits, Hot Air Stations, and Microscopes from the Mechanicpk catalog. As pad work grows, a Soldering Station with finer temperature control is the natural next step up.
| Weight | 0.25 kg |
|---|
Key Features
- ✓100,000 uniform solder balls per bottle
- ✓Sn63/Pb37 eutectic alloy
- ✓183°C melting point for single-step reflow
- ✓Uniform ball size for repeatable pad height
- ✓Low-oxidation composition with minimal residue
- ✓iPhone-specific PB01 variant
- ✓Compact 16 mm x 16 mm x 32 mm bottle
- ✓Suited to precision work under a microscope
Specifications
| Brand | 2UUL |
|---|---|
| Model | PB01 |
| Category | Solder Balls / Reballing Consumables |
| Compatibility | iPhone motherboard solder pad rework |
| Material | Sn63/Pb37 (Tin 63% / Lead 37%) |
| Melting Point | 183°C |
| Quantity | 100,000 balls per bottle |
| Dimensions | 16 mm x 16 mm x 32 mm (bottle); 131 mm x 105 mm x 48 mm (packing) |
| Weight | 5.5 g (net) |
Common Repair Uses
- ✓Real pad rework and reballing scenarios on the repair bench.
- ✓Restoring missing solder pads on iPhone mainboards
- ✓Rebuilding lifted pads after a drop or board damage
- ✓Reballing CPU, GPU, or chipset components
- ✓BGA and CSP pad restoration
- ✓Fixing a hardware fault at the pad before IC replacement
- ✓Precision micro-soldering under a microscope
Compatible Devices
- ✓iPhone motherboards (PB01 is the iPhone variant; the Android variant is PB02). Device-level model lists are not published, so the scope stays at the iPhone logic board.
- ✓iPhone logic board solder pads
- ✓Pads under BGA packages on iPhone boards
- ✓Pads under CSP packages on iPhone boards
- ✓Chipset, CPU, and GPU component pads on iPhone mainboards
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is the 2UUL PB01 for iPhone or Android?
What alloy and melting point do these solder balls have?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



