2UUL DA28 FlatCut Underfill Removal Blades 5pcs
₨ 600
2UUL DA28 FlatCut Underfill Removal Blades
The 2UUL DA28 FlatCut is a solder pad underfill removal blade set for board-level work on phone and electronics PCBs. Each box holds five steel blades measuring 37 x 9 x 0.5 mm, so a fresh edge is always ready when one dulls. The flat-cut profile lifts hardened underfill from around an IC and levels leftover residue on the pads before you reball or seat a replacement chip. Pakistani technicians reach for it after hot air removal on CPU, eMMC and charging IC jobs. Order the 5pcs box from Mechanicpk for your bench or service center.
In stock
Solder Pad Underfill Removal Blade for Board-Level Repair
A solder pad underfill removal blade decides how clean your pads look before the new IC goes down, and the 2UUL DA28 FlatCut is built for that exact stage. One box gives you five flat-cut steel blades, each 37 x 9 x 0.5 mm. At half a millimeter thick, the blade slides into the gap between hardened underfill and the board. The flat edge then works across the pad surface instead of digging in with a point. You pick it up once the chip is off and the bare footprint still carries cured glue and old solder.
How the FlatCut Profile Works on the Bench
Pointed blades concentrate pressure on one spot, and on a fine-pitch footprint that spot can scar the solder mask or lift a pad. The DA28 uses a straight, flat edge instead. You lay the blade low against the board and push forward in short, controlled strokes, and the contact spreads over a wider line. That geometry suits two jobs: peeling cured underfill from the edges of a removed IC, and leveling the solder left on the pads so the surface sits flat.
The 9 mm blade width covers a row of pads in a single pass, which cuts the number of strokes on a large CPU or eMMC footprint. The 0.5 mm thickness still lets you reach the tight gaps beside shield frames and neighboring components. Steel construction holds the edge through several boards. When an edge dulls, you swap in the next blade from the box and keep the same cutting quality across the job.
Where It Fits in Your Repair Workflow
Underfill removal sits between chip removal and cleaning in the PCB repair process. You heat the board with your hot air station, lift the IC, and scrape the cured glue before anything else touches the pads. After the blade pass, you clean with flux and braid on your soldering station, then inspect the footprint under a microscope. Clean, level pads decide whether your reballing kit stencil seats properly and whether the new ball array bonds on the first attempt.
This workflow covers everyday bench faults: a dead phone after a failed flash that traces back to a bad eMMC or UFS joint, a charging issue that ends in a charging IC change (IC change karna), and a hardware fault that needs CPU reballing. Each job leaves underfill residue, and the DA28 handles that step. Hold the board firmly in a PCB holder before you scrape, because a board that shifts mid-stroke causes more damage than any blade edge. After rework, test continuity with your multimeter and confirm the repair with your test box or programmer.
Why Technicians Choose a Dedicated Blade Box
A set of five blades keeps your cleaning step consistent. Instead of forcing one worn edge across a delicate footprint, you rotate to a fresh blade and keep the pressure light. Repair shops that process boards daily burn through edges quickly, so a five-piece box lowers your cost per board and keeps pad quality steady between technicians.
The DA28 targets one task, underfill and solder pad cleanup, and it does that task with a purpose-made flat profile. That focus makes it a practical addition next to your hot air stations, soldering stations and microscopes. Mechanicpk supplies the 2UUL DA28 FlatCut box for workshops, service centers and training institutes across Pakistan that need dependable consumables for CPU, NAND and IC rework.
| Weight | 0.6 kg |
|---|
Key Features
- ✓Five blades per box
- ✓Flat-cut profile for underfill and pad work
- ✓37 x 9 x 0.5 mm blade size
- ✓Ultra-thin 0.5 mm edge for tight gaps
- ✓Steel blade construction
- ✓Sharp edge for clean underfill separation
- ✓Designed for solder pad cleaning on mobile PCBs
- ✓Spare blades keep a fresh edge on every job
Specifications
| Brand | 2UUL |
|---|---|
| Model | DA28 FlatCut |
| Category | Mobile Repair Tools — Glue Removal Blades |
| Compatibility | Universal; blade tool for underfill and solder pad cleaning, not device-specific |
| Material | Steel |
| Dimensions | 37 x 9 x 0.5 mm (per blade) |
| Weight | 14.5 g (gross, boxed) |
| Quantity | 5 pcs per box |
Common Repair Uses
- ✓Underfill glue removal and solder pad cleaning during board-level repair
- ✓Removing cured underfill around an IC after hot air lift-off
- ✓Cleaning solder pads before reballing
- ✓Leveling leftover solder on pads
- ✓Clearing glue residue after CPU or eMMC removal
- ✓Scraping adhesive from tight PCB gaps
- ✓Preparing pads for a new IC installation
Compatible Devices
- ✓Universal — not device-specific; applies to any board with underfill glue or solder pads
- ✓Smartphone motherboards
- ✓Tablet PCBs
- ✓General electronics PCBs
- ✓CPU, NAND and IC underfill areas
- ✓Solder pads on removed-chip footprints
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What size are the 2UUL DA28 FlatCut blades?
Can the DA28 FlatCut blade clean solder pads after IC removal?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock



