YCS S1-160W Ultra Soldering Iron Station for Mobile Repair

₨ 26,000

YCS S1-160W Digital Soldering Station

The YCS S1-160W Ultra Soldering Iron station brings program-chip temperature control, temperature compensation, and automatic sleep to your mobile repair bench. It drives T245, T210 and T115 handles, supports C245, C210 and C115 tips, and runs on 110V or 220V depending on the variant. The four-segment memory display keeps your settings visible while you work on charging ports, battery connectors, SMD pads, and BGA-area cleanup. The package includes a handle, one tip, a sponge, copper cleaning balls, and a power cable. Choose it when you need controlled, repeatable heat for daily PCB repair in your workshop.

In stock

11 People watching this product now!
Description

YCS S1-160W Soldering Station for Mobile Repair: Technical Overview

The YCS S1-160W Ultra Soldering Iron station gives your repair bench a program-chip temperature controller, automatic sleep, and plug-and-play support for three handle families. When you compare a YCS S1-160W soldering station for mobile repair against basic dial irons, control decides the purchase. This unit holds your set temperature while the tip works through heavy ground planes and fine SMD pads alike. One base unit drives T245, T210 and T115 handles, so a single station covers charging port replacement, connector work, and micro-soldering. Pakistani repair shops that push boards through the bench all day get a controller that reacts fast and keeps the tip at temperature.

Program-Chip Temperature Control That Holds Its Set Point

Conventional irons regulate heat by switching AC voltage, and the tip temperature drifts the moment it touches a large copper area. The S1-160W replaces that approach with a program chip that controls temperature directly. Supplier data states that the tip heats quickly and accurately and melts solder in about two seconds. The temperature compensation function adds a second layer. It adjusts power during soldering so the tip stays at the temperature you set while it pulls heat into the joint. You see the benefit on charging flex pads, battery connector terminals, and shield frames, where a drooping tip leaves a cold joint and sends the phone back with the same charging issue. The four-segment memory display keeps your temperature settings in view on the bench, so you check the set point at a glance instead of guessing.

Handle and Cartridge Compatibility: T245, T210 and T115

The controller runs T245, T210 and T115 handles plug and play, and it supports C245, C210 and C115 tips. That range matters because each cartridge family suits a different joint size. C245 cartridges carry more thermal mass for large pads, ground connections, and shield cans. C210 cartridges suit general SMD work, connector pads, and jumper wire repair. C115 cartridges fit fine-pitch pads and micro-soldering under a microscope. You buy the base station once and add handles as your work moves from basic repairs toward board-level jobs, which gives you a clear upgrade path inside one ecosystem. The package includes one handle and one tip, so confirm which handle variant ships with your unit and order extra cartridges for the pad sizes you solder most.

Automatic Sleep, Voltage Options, and Bench Safety

Automatic sleep puts the iron into standby when it sits idle. That cuts idle heating during long diagnostic sessions and reduces tip wear between boards. YCS lists the S1-160W for 110V and 220V supplies, and some suppliers ship 110V-only units. Pakistani mains runs at 220V, so confirm the 220V variant before you order. The box adds a sponge and copper cleaning balls, which you use to wipe oxide off the tip and keep heat transfer consistent. Clean the tip before each joint and re-tin it before you park the iron. A tip kept clean and tinned transfers heat faster and lasts longer.

Where the S1-160W Fits in a Mobile Repair Workflow

A typical board-level repair follows a fixed sequence. You diagnose with a multimeter, remove the failed IC or shield with a hot air station, then clean the pads and fit the new part. The soldering station owns the hand-soldering steps in that sequence: tinning pads, clearing solder residue, fitting charging ports, replacing battery connectors, and laying jumper wires across damaged tracks on a dead phone board. After reballing work, you dress the pads with the iron before the chip goes back down. Mount the board in a PCB holder, work under a microscope when you use C210 or C115 cartridges, and check continuity with your multimeter before you reassemble. A hardware fault that looks like a dead phone often traces back to one lifted pad or one cold joint, and a controlled iron fixes that cleanly.

Why the YCS S1-160W Soldering Station for Mobile Repair Suits Your Bench

Soldering stations sit at the core of every repair bench, and this model targets technicians who want chip-based control without stepping up to a full rework system. The station suits a one-man shop in Karachi as well as a service center that handles dozens of boards a day, because the same controller serves light and heavy joints through different cartridges. Build the rest of your setup around it with hot air stations for IC removal, microscopes for fine-pitch inspection, reballing kits for BGA work, and PCB holders for stable board positioning. When you need more soldering stations or matching tips, browse the Mechanicpk soldering category and match the cartridge to your most common repair.

Additional information
Weight2.5 kg
Q & A
Please login to post questions

Key Features

  • Program-chip temperature control for fast, accurate heating
  • Melts solder in about two seconds per supplier data
  • Temperature compensation keeps the tip at the set temperature
  • Automatic sleep function
  • Four-segment memory display
  • Plug-and-play with T245, T210 and T115 handles
  • Supports C245, C210 and C115 tips
  • Includes handle, tip, sponge, copper cleaning balls, and power cable

Specifications

BrandYCS
ModelS1-160W
CategoryDigital Soldering Station
CompatibilityT245, T210 and T115 handles; C245, C210 and C115 tips
TechnologyProgram-chip temperature control with temperature compensation and automatic sleep
Input Voltage110V / 220V (variant-specific)
Power Rating160W

Common Repair Uses

  • Hand-soldering tasks on mobile phone boards
  • Charging port replacement and pad repair
  • Battery connector replacement
  • SMD component replacement
  • Jumper wire repair on damaged tracks
  • Pad cleaning and tinning after IC removal
  • Pad dressing after reballing
  • Micro-soldering with fine C115 or C210 tips
  • Shield frame and ground-plane soldering with C245 tips

Compatible Devices

  • Universal bench tool, not tied to any phone brand or model
  • Universal bench tool, not device-specific
  • T245 handles
  • T210 handles
  • T115 handles
  • C245 cartridge tips
  • C210 cartridge tips
  • C115 cartridge tips
  • Mobile phone PCBs and general electronics boards (SMD and BGA-area work)

FAQ

What is the product name?
The product name is YCS S1-160W Ultra Soldering Iron.
What is the brand of this product?
The brand of this product is YCS.
What is the model of this product?
The model of this product is S1-160W.
What is this product used for?
This product is used for PCB, SMD, and BGA-area soldering in mobile phone and electronics repair.
Which devices are compatible with this product?
This product is a universal bench tool. It works with T245, T210 and T115 handles and C245, C210 and C115 tips.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which handles and tips does the YCS S1-160W support?
It supports T245, T210 and T115 handles and C245, C210 and C115 tips.
Does the YCS S1-160W run on 220V in Pakistan?
YCS lists the S1-160W for 110V and 220V supplies, but some suppliers ship 110V-only units. Confirm the 220V variant before you order.