Yihua YH-852D+ 2-in-1 Hot Air & Soldering Iron Station

₨ 1

Yihua YH-852D+ 2 in 1 Hot Air and Soldering Station

The Yihua YH-852D+ combines a hot air gun and a soldering iron in one station with dual LED displays. You get adjustable hot air from 100 to 480 °C for lifting and reflowing SMD parts, and an iron that heats from 200 to 480 °C for joints and wire work. Each output shows its own temperature, so you confirm both settings before you start. The hot air gun comes with 10 mm, 8 mm and 5 mm nozzles to focus heat on different packages. The station suits mobile repair benches, laptop workshops and training labs that handle SMD ICs, connectors and chip card components every day.

Out of stock

11 People watching this product now!
Description

2 in 1 Hot Air and Soldering Station for SMD Rework

A 2 in 1 hot air and soldering station gives you two heat sources on one bench, so you avoid switching between separate units mid-job. The Yihua YH-852D+ pairs a hot air gun for lifting and reflowing surface mount parts with a soldering iron for pins, pads and wire joints. Both outputs run from the same chassis, and each has its own LED temperature readout. That layout suits a technician who moves between chip-level removal and general board repair during the same shift. The hot air side handles ICs, connectors and shielded parts, while the iron finishes the pads and fine soldering that follows. Setting both outputs before you pick up a handle keeps your workflow steady from the first joint to the last.

Where This Station Fits in Your Repair Workflow

Most board-level jobs follow a sequence: diagnose the fault, remove the faulty part, clean the pads, fit the replacement and test the result. The YH-852D+ supports the middle of that sequence, where heat does the real work. Hot air melts the joints under a component so you can lift it cleanly. The soldering iron then tidies the pads and handles any connector pins that need hand attention. Keeping both tools on one station means you move from removal to repair without changing benches or waiting for a second unit to heat up. The station sits well alongside a microscope, a multimeter and your usual pad-cleaning supplies. Plan each job before you power on, so you know which output you need first and which parts need protection from heat.

Hot Air Gun Performance and Nozzle Choice

The hot air gun covers a 100 to 480 °C range and provides adjustable airflow, so you can match both heat and air volume to the part under the nozzle. Lower airflow suits small chips that sit close to fragile traces, while higher airflow helps when you lift shielded cans or larger packages. The 10 mm, 8 mm and 5 mm nozzles let you concentrate heat on the footprint without blowing neighboring components off the board. Start with a moderate temperature, then raise it in small steps until the solder on the pads melts. A gun that holds its setpoint gives you repeatable results across a full shift, which matters when you lift several ICs in a row. Hold the nozzle a few millimeters above the component and move it in slow circles so the joints warm evenly.

Soldering Iron Output for Pins and Joints

The soldering iron runs from a 26 V AC output and heats between 200 and 480 °C. That range covers lead-free solder as well as general through-hole and wire work. The iron recovers temperature quickly after you touch a cold pad, which keeps your joints consistent across a long session. Choose a tip that matches the pad size: a fine tip works on flex connector pins and small resistors, while a broader tip moves enough heat into power pins and wire joints. Set the temperature on the iron’s dedicated display and leave it there for the whole session, so you do not chase drift between joints. The iron’s ESD-safe design protects sensitive chips from static discharge during extended bench work. Wipe the tip on a damp sponge after each joint to keep heat transfer steady and the solder flowing cleanly.

Dual Display Control and Temperature Setting

Two LED displays show the set temperature for the hot air gun and the iron separately, so you always know which output is active. Each output has its own adjustment, and the readout updates while the heater reaches the target value. Watch the display before each reflow and confirm that the setting matches the component and the solder you use. A steady setpoint protects heat-sensitive parts, while a higher setting shortens the time you spend on each pad. Note the temperature on the display before you start a job, then adjust in small steps if the first attempt does not melt the joints. Clear, separate readouts reduce the guesswork that often leads to lifted pads or overheated components.

Chip Packages and Components Covered

The YH-852D+ handles SMD components in SOIC, QFP, PLCC and BGA packages, along with chip card components. Each package has its own heat demands. Small outlines and chip card parts need a focused nozzle and moderate airflow, while larger QFP and PLCC packages benefit from even heat across all sides of the body. BGA removal calls for patient, uniform heating, so move the nozzle in circular passes rather than holding one spot. For through-hole parts and wire joints, switch to the iron output and work from the component side. A stainless steel holder keeps the hot air gun steady between passes, and a plastic stand keeps the iron away from flammable material when you pause.

Bench Setup and Safe Handling

Set the station on a stable, heat-resistant surface with clear space around both handles. Work in a ventilated area, because flux fumes build up quickly during hot air work. Wear eye protection when you lift components with airflow, since small parts can shift under the nozzle. Keep the power cord clear of the heat zone so it cannot touch hot metal. Let the hot air gun cool on its holder before you store it, and return the iron to its stand between joints. Use the station with lead-free solder and confirm the temperature before each job, so your joints stay reliable and your components stay protected.

Additional information
Weight2.0 kg
Q & A
Please login to post questions

Key Features

  • 2 in 1 design with a hot air gun and soldering iron on one station
  • Hot air range of 100 to 480 °C with adjustable airflow
  • Soldering iron range of 200 to 480 °C for joints and pins
  • Dual LED displays that show each output’s temperature
  • 10 mm, 8 mm and 5 mm hot air nozzles included
  • ESD-safe soldering iron design for sensitive components
  • Stainless steel holder for the hot air gun and plastic stand for the iron
  • Built for lead-free soldering work

Specifications

BrandYihua
ModelYH-852D+
CategorySoldering and Rework Station
CompatibilityUniversal, not device-specific
Supported DevicesSMD components in SOIC, QFP, PLCC, BGA and chip card packages
TechnologyHot air gun and soldering iron in one unit, dual LED temperature displays, adjustable hot air airflow
Input VoltageAC 220 V ±10%, 50 Hz
Output VoltageSoldering iron 26 V AC ±10%, 50 Hz

Common Repair Uses

  • Removing and fitting SMD ICs on mobile logic boards
  • Desoldering and replacing charging port connectors
  • Lifting BGA chips for removal or replacement
  • Soldering flex cable and display connector pins
  • Reworking SMD resistors and capacitors after a short
  • Lifting shielding cans during board-level repair
  • Soldering wires and jumpers on PCB traces
  • Loosening glued parts with controlled hot air

Compatible Devices

  • Universal, not device-specific (bench tool for SMD and through-hole work)
  • SOIC chip packages
  • QFP chip packages
  • PLCC chip packages
  • BGA chip packages
  • Chip card components
  • SMD resistors and capacitors
  • Through-hole pins and wire joints
  • Any PCB layout that accepts hot air and iron work

FAQ

What is the product name?
The product name is Yihua YH-852D+ 2 in 1 Hot Air and Soldering Station.
What is the brand of this product?
The brand of this product is Yihua.
What is the model of this product?
The model of this product is YH-852D+.
What is this product used for?
This product is used for removing, fitting and soldering SMD components, along with pin and wire soldering.
Which devices are compatible with this product?
This product is compatible with universal, non-device-specific SMD and through-hole repair work, including SOIC, QFP, PLCC, BGA and chip card packages.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What temperature range does the hot air gun reach?
The hot air gun operates from 100 to 480 °C with adjustable airflow.
What voltage does the soldering iron use?
The soldering iron runs from a 26 V AC output at 50 Hz.