Amaoe WSR1 Qualcomm WTR/SDR Reballing Stencil 0.12mm

₨ 599

Qualcomm WTR SDR Reballing Stencil

The Amaoe WSR1 packs the footprints of Qualcomm WTR, SDR, IF and RF ICs onto one 0.12 mm steel stencil. You can reball transceivers from the WTR1605/L generation through WTR5975, plus SDR660, SDR845, SDR8150 and SDX55M, without switching templates. One plate replaces a drawer of single-IC stencils, so your bench stays tidy and your reballing sequence stays repeatable. If you search for a Qualcomm WTR SDR reballing stencil in Pakistan, the WSR1 gives you named coverage across these families and a pad layout you can check against the IC marking on your board.

In stock

15 People watching this product now!
Description

Amaoe WSR1 Stencil for Qualcomm RF Transceiver Reballing

The Amaoe WSR1 is a Qualcomm WTR SDR reballing stencil that puts several RF transceiver and IF IC footprints on one 0.12 mm steel plate. Mechanicpk lists it for technicians who rework Qualcomm radio-frequency ICs at board level and want one template for the WTR1605/L, WTR2605, WTR3905, WTR4905, WTR2965, WTR5975 and SDR845 families. You set it over a cleaned IC, work solder through the apertures, and reflow under your hot air station. The result is a uniform ball pattern across the whole footprint, which matters when a single bridged ball leaves you with the same network issue you started with.

Qualcomm WTR SDR Reballing Stencil Coverage by IC Family

Distributor listings for the WSR1 name these Qualcomm parts: WTR1605/L, WTR1620, WTR1625/L, WFR1620, WTR2600, WTR2605, WFR2600, WTR2955, WTR2965, WTR3905, WTR3925, WTR4605, WTR4905 and WTR5975 on the transceiver side, plus SDR660, SDR735, SDR845, SDR865/686, SDR8150, SDX55M and SMR526 on the SDR and related side. Check the marking on your board against that list before you start, because coverage stops at those families. The WSR1 targets Qualcomm silicon only. Listings name no MediaTek or Exynos RF parts, so you need a separate stencil for those boards.

Where the WSR1 Fits in Your Repair Workflow

Network issue and no-signal complaints often trace back to a hardware fault in the RF section of the board. Once your diagnosis points at the WTR or SDR chip, you lift the IC, clean the pads, and reball it. That reballing step is the core of IC change karna on a Qualcomm board, and the WSR1 handles it without forcing you to hunt through a drawer of single-IC templates. After reflow, you check the rails with your multimeter, power the board through a test box, and confirm the radio comes back before you close the phone.

If the phone still shows hang on logo or a boot loop issue after the RF work, the fault has moved to the software or storage side. Switch to your ISP pinout tools, eMMC programmers or UFS adapters at that point instead of reworking the same IC twice.

Build Details and Bench Setup

The stencil measures 0.12 mm thick and uses stainless steel with square apertures, according to distributor listings. That thickness controls how much solder each pad receives, so you get consistent ball height without trimming or touching up afterward. The pack contains one stencil and weighs about 0.01 kg, which keeps it easy to store next to your other templates.

Good results depend on the rest of your bench as much as the stencil. A PCB holder keeps the board flat while you align the template, a microscope lets you confirm every aperture sits over its pad, and a soldering station with a clean tip handles pad preparation. If you reball often, a full set of reballing kits covers ball sizes and flux, and a stable hot air station controls the reflow. Technicians who start with this single stencil usually grow into a wider Qualcomm stencil range as their repair mix expands.

Buying Notes for Pakistani Repair Shops

A repair shop in Pakistan that handles Qualcomm boards every week gets the most from the WSR1, because one template covers many jobs and keeps your consumables predictable. Compare the IC marking on the boards you see most against the coverage list above, then decide whether one WSR1 serves your queue or whether you also need a second stencil for non-Qualcomm RF parts. Buyers who work on a mix of dead phone cases and network issue cases usually stock this template early, since RF ICs can fail after a drop, liquid contact or a poor solder job from an earlier repair. Order the stencil together with flux, solder balls and a PCB holder so your reballing setup arrives complete. If you train new technicians, a single-plate stencil also shortens the learning curve, because your trainee matches one footprint to one IC instead of memorising a stack of separate templates.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • One 0.12 mm plate covers multiple Qualcomm WTR, SDR, IF and RF IC footprints
  • Named coverage from WTR1605/L through WTR5975
  • SDR660, SDR735, SDR845, SDR865/686 and SDR8150 included
  • SDX55M and SMR526 included
  • Stainless steel construction
  • Square apertures
  • Single-stencil pack
  • Light 0.01 kg unit that stores easily with other templates

Specifications

BrandAmaoe
ModelWSR1
CategoryBGA Reballing Stencil
CompatibilityQualcomm WTR, SDR, IF and RF ICs (WTR1605/L to WTR5975, SDR660 to SDR8150, SDX55M, SMR526)
Technology0.12 mm square-aperture BGA reballing stencil
MaterialStainless steel
Weight0.01 kg

Common Repair Uses

  • Qualcomm RF transceiver and IF IC reballing at board level
  • Reballing a lifted WTR transceiver after IC removal
  • Reballing SDR-series ICs during RF section repair
  • IC change karna on Qualcomm boards with network issue
  • Reworking a no-signal board after a hardware fault in the RF section
  • Rebuilding balls after liquid-damage cleaning of RF ICs
  • Re-reballing an IC after a poor earlier solder job
  • Replacing a damaged RF IC with a fresh part
  • Training technicians on one-plate Qualcomm RF reballing

Compatible Devices

  • Qualcomm-based boards carrying the WTR, SDR, IF and RF ICs below (chipset-family scope; not tied to specific phone models)
  • WTR1605/L, WTR1620, WTR1625/L, WFR1620
  • WTR2600, WTR2605, WFR2600
  • WTR2955, WTR2965
  • WTR3905, WTR3925
  • WTR4605, WTR4905
  • WTR5975
  • SDR660, SDR735, SDR845
  • SDR865/686, SDR8150, SDX55M, SMR526

FAQ

What is the product name?
The product name is Amaoe Stencil WSR1.
What is the brand of this product?
The brand of this product is Amaoe.
What is the model of this product?
The model of this product is WSR1.
What is this product used for?
This product is used for reballing Qualcomm WTR, SDR, IF and RF ICs during board-level mobile repair.
Which devices are compatible with this product?
This product is compatible with Qualcomm-based boards that carry the WTR, SDR, IF and RF ICs listed in the specifications. It is not tied to specific phone models.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which Qualcomm ICs does the Amaoe WSR1 stencil cover?
Distributor listings name WTR1605/L, WTR1620, WTR1625/L, WFR1620, WTR2600, WTR2605, WFR2600, WTR2955, WTR2965, WTR3905, WTR3925, WTR4605, WTR4905, WTR5975, SDR660, SDR735, SDR845, SDR865/686, SDR8150, SDX55M and SMR526.
Can I use the WSR1 stencil on MediaTek or Samsung Exynos RF ICs?
No. The WSR1 targets Qualcomm WTR, SDR, IF and RF ICs, and listings name no MediaTek or Exynos parts. Choose a separate stencil for those boards.