Amaoe MT6799W BGA Reballing Stencil for MediaTek CPU
₨ 599
MT6799W Reballing Stencil
The Amaoe MT6799W BGA reballing stencil gives you a precise 0.12mm steel template for restoring solder balls on the MediaTek MT6799W package. Square round holes guide each ball into position, and a deformation-resistant steel body keeps the pattern flat through repeated heating. You use it after chip removal, once you clean the pads and need an even, repeatable ball layout on the CPU. Mechanicpk supplies this stencil to repair shops and service centers across Pakistan that handle Helio X30 boards. Check the chip marking on your board before you order, then pair the stencil with your reballing kit, hot air station, and microscope.
In stock
MT6799W BGA Reballing Stencil for Helio X30 Board Repair
The MT6799W BGA reballing stencil from Amaoe gives you a repeatable way to restore solder balls on the MediaTek MT6799W package, part of the Helio X30 platform. MediaTek built the Helio X30 as a 10nm deca-core SoC, and the dense ball grid under it leaves no room for freehand tinning. When a board lands on your bench dead after a drop or a failed reflow, you remove the chip, clean the pads, and need every ball to sit exactly where the ball map places it. This template handles that job.
Stencil Build and Hole Design
Amaoe cuts this template from 0.12mm steel mesh. The deformation-resistant material stays flat through repeated heating cycles, so the openings hold their position from one job to the next. Square round holes guide each ball into its seat and release solder cleanly when you lift the stencil off the chip. Pin locations follow the MT6799W ball layout, which lets the openings line up with the pads on a properly cleaned package. Amaoe also lists MT6799W RAM among the packages covered by its multi-chip MediaTek stencil series, so confirm the cut pattern against your chip before you start.
Where It Fits in Your Reballing Workflow
You reach for this stencil after the hardware fault diagnosis is done. Lift the CPU with your hot air station, then clean the board pads and the chip underside with flux and solder wick under a microscope. Check the area around the CPU with a multimeter for shorts before you commit to refitting. Seat the chip in your PCB holder or jig, lay the stencil over it, and align the openings with the pads. Place your balls or apply paste, heat the chip, let it cool, and lift the stencil. Inspect the result under the microscope, then reflow the chip back onto the board with your soldering station or hot air setup. Reballing kits, PCB holders, and flux all come from the same bench, so you can build the full workflow from Mechanicpk stock.
Why Technicians Choose a Chip-Specific Stencil
A universal stencil forces you to compromise on pitch and ball count. A chip-specific template like this one matches the MT6799W layout, so you spend less time correcting misaligned balls and more time moving boards through the queue. That matters on a dead phone job, where one bad ball can send you back to square one after you already did the IC change. It also helps with boot loop issue and hang on logo cases that trace back to lifted or cracked balls under the CPU.
Once the board powers up, your workflow continues on the software side. Test boxes, ISP pinout tools, eMMC programmers, and UFS adapters handle storage access, flashing, and software marna jobs on boards that need them. This stencil covers the hardware step that comes before all of that. Buy it when your bench handles MediaTek Helio X30 boards and you want a rigid, correctly patterned template ready before the next job arrives.
| Weight | 0.1 kg |
|---|
Key Features
- ✓0.12mm steel mesh template
- ✓Deformation-resistant material that stays flat through repeated heating
- ✓Square round hole design for clean ball seating and release
- ✓Precise pin locations matched to the MT6799W ball layout
- ✓Suits a general rework station setup
- ✓Thin, rigid profile that works with PCB holders and reballing jigs
- ✓Supplied as a single stencil piece
- ✓Fits the CPU reballing step in a hardware-first repair workflow
Specifications
| Brand | Amaoe |
|---|---|
| Model | MT6799W |
| Category | BGA Reballing Stencil |
| Compatibility | MediaTek MT6799W CPU (Helio X30 platform) |
| Technology | BGA reballing, 0.12mm steel template, square round holes |
| Material | Steel mesh |
Common Repair Uses
- ✓Reballing work on MT6799W-based boards after chip removal.
- ✓CPU reballing after lifting the chip with hot air
- ✓Restoring solder balls on a dead phone after a drop
- ✓IC change karna jobs where you refit the original chip
- ✓Repair of boot loop issue and hang on logo faults caused by damaged balls
- ✓Tin planting on a cleaned chip before reflow
- ✓Reballing the MT6799W RAM package where the stencil pattern matches
Compatible Devices
- ✓Chipset-level scope. The stencil targets boards carrying the MediaTek MT6799W package (Helio X30 platform). Amaoe does not publish a verified phone-model list for it.
- ✓MediaTek MT6799W CPU package
- ✓MediaTek MT6799W RAM package (listed by Amaoe in its multi-chip MediaTek stencil series)
- ✓Boards built on the MediaTek Helio X30 (MT6799) platform
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does this stencil cover both the MT6799W CPU and the MT6799W RAM?
What thickness is this stencil, and why does it matter for reballing?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock


