2UUL DW11 SolderAway Desoldering Wick 2.0mm 10 Rolls/Box

₨ 2,200

DW11 SolderAway Wick, 10-Roll Box

The 2UUL DW11 SolderAway is a desoldering wick for mobile repair, supplied as a 10-roll box for busy workshops. Each roll measures 1.5 m long and 2.0 mm wide. The plain-knit, fluorine-free braid conducts heat fast and leaves little residue on the pad, so you clear old solder from BGA, CPU and NAND pads without overheating the board. You stock one box and cover weeks of pad cleanup after IC change karna, reballing prep and hardware fault repairs. Mechanicpk supplies the DW11 across Pakistan for technicians, service centers and repair shops that buy consumables in volume.

In stock

15 People watching this product now!
Description

Desoldering Wick for Mobile Repair: DW11 SolderAway 2.0mm Braid

The 2UUL DW11 SolderAway is a desoldering wick for mobile repair built for one job: lifting leftover solder from motherboard pads once you remove a chip. A box contains 10 rolls, and each roll measures 1.5 m by 2.0 mm. 2UUL weaves the braid in a plain knit and finishes it fluorine-free, so heat moves quickly from your iron tip into the joint and little residue stays behind. A busy bench burns through wick fast, which is why buyers order it by the box instead of by the single roll.

How the Braid Lifts Solder Off the Pad

Lay the wick flat over the pad, press your heated iron tip onto the braid, and the molten solder wicks into the weave. The plain knit conducts heat from the tip to the joint quickly, so the solder liquefies before the pad overheats. This matters on multilayer phone boards, where long dwell time lifts pads and tears traces. 2UUL’s guidance says to keep the wick under heat for no more than 5 seconds per pass. Drag the braid slowly along the pad, cut away the used section once it fills with solder, and continue with fresh braid. Fresh braid absorbs better than a loaded section, so trim often instead of forcing it.

Where It Fits in Your Repair Workflow

After IC change karna on a dead phone, the pads under a BGA CPU, NAND or eMMC chip carry uneven solder blobs and bridges. You flatten those pads with wick before you reball the chip or place a replacement. The same braid cleans charging IC pads, connector pads and shorted SMD pads behind a charging issue or a hang on logo fault. Pair it with a hot air station to release the chip, a soldering station to work the pads, and a microscope to confirm the finish. A clean, flat pad gives your reballing kit stencil an even surface, and a PCB holder keeps the board steady while you drag the braid.

Choosing the Right Width and Box Size

The DW11 uses 2.0 mm braid. That width suits mid-size pad areas and rows of pads on phone motherboards, where you clear several joints in one pass. For very fine pitch work, match your braid width to the pad width rather than using the widest wick you own. A narrow pad under a wide braid draws heat and solder from neighboring points. The 10-roll box suits repair shops, training institutes and service centers where several technicians share consumables. You hand each technician a roll, and the 1.5 m length lasts through many pad cleanups because each pass consumes only a few centimeters.

Why Technicians Pick the DW11

The braid saves time at the bench because it pulls solder quickly and leaves the pad ready for the next step. The low-residue finish reduces the cleanup you do with isopropyl alcohol afterward, and the fast heat transfer protects pads on dense boards. Mechanicpk stocks the DW11 for buyers who know the repair trade and want a dependable consumable they can reorder without guessing.

Additional information
Weight0.2 kg
Q & A
Please login to post questions

Key Features

  • 2.0 mm wide, 1.5 m long braid on each roll
  • 10 rolls per box for workshop volume
  • Plain-knit weave for fast heat conduction
  • Fluorine-free construction with low residue
  • Strong solder absorption for quick pad clearing
  • Reduces thermal stress on circuit boards when you follow the 5-second limit
  • Suits BGA, CPU, NAND and eMMC pad cleanup
  • Works with standard soldering irons and stations

Specifications

Brand2UUL
ModelDW11 SolderAway
CategoryDesoldering Wick / Solder Removal Braid
CompatibilityUniversal, not device-specific
TechnologyPlain-knit, fluorine-free braided wick
Width2.0 mm
Length per Roll1.5 m
Pack Quantity10 rolls per box

Common Repair Uses

  • Removing leftover solder from motherboard pads after chip removal and cleaning pads before reballing or chip replacement.
  • Flattening BGA pads after CPU removal
  • Cleaning NAND and eMMC pads before reballing
  • Clearing solder bridges between pads
  • Preparing charging IC pads for replacement
  • Removing excess solder from connector pads
  • Cleaning pads after a dead-after-flash chip swap
  • Correcting solder blobs after rework
  • General PCB motherboard solder cleanup

Compatible Devices

  • Universal desoldering consumable. It works on any PCB pad, so it is not tied to specific phone models or brands.
  • BGA CPU pads on mobile phone motherboards
  • NAND and eMMC chip pads
  • Charging IC pads
  • Connector pads (display, battery, charging port)
  • SMD component pads after rework
  • Shorted or bridged pads
  • Through-hole solder joints
  • General PCB solder cleanup

FAQ

What is the product name?
The product name is 2UUL DW11 SolderAway Desoldering Wick 2015 10 Rolls/Box.
What is the brand of this product?
The brand of this product is 2UUL.
What is the model of this product?
The model of this product is DW11 SolderAway.
What is this product used for?
This product is used for removing leftover solder from PCB and motherboard pads during mobile phone repair and rework.
Which devices are compatible with this product?
This product is a universal desoldering consumable. It works on any PCB pad and is not limited to specific phone models.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What width and length is each roll of the 2UUL DW11 desoldering wick?
Each roll is 2.0 mm wide and 1.5 m long, and one box contains 10 rolls.
How long can I heat the desoldering wick on the board?
Keep the wick under heat for no more than 5 seconds per pass to avoid damaging the pad or nearby components.