Amaoe RF2 BGA Reballing Stencil for RF Power Amplifier IC

₨ 599

Amaoe RF2 BGA Stencil for RF ICs

The Amaoe RF2 BGA stencil gives your bench a dedicated steel mesh template for reballing RF power amplifier ICs. Amaoe lists the RF1 and RF2 series for part numbers 77031, QPM5677, 53735 and 78191-11. You match the footprint, press solder tin through the apertures, and heat the tin into balls. The deformation-resistant mesh holds its shape, and the square round holes keep each pin position precise. Mechanicpk supplies this stencil to Pakistani repair shops and service centers that handle RF-section hardware fault jobs and need repeatable reballing results.

In stock

16 People watching this product now!
Description

Amaoe RF2 BGA Stencil for RF Power Amplifier IC Reballing

An RF power amplifier IC rarely comes off a board with its solder balls intact. When you do IC change karna on the RF section, the amplifier IC needs a fresh set of balls before it goes back down, and a stencil rebuilds them in a repeatable way. The Amaoe RF2 BGA stencil is a steel mesh reballing template from Amaoe, offered together with the RF1 option under one listing. Amaoe ties the RF1 and RF2 series to power amplifier IC part numbers 77031, QPM5677, 53735 and 78191-11. Check your IC’s marking and pad layout against the RF2 option, then pick the variant that fits your job before you order.

How the RF2 Stencil Rebuilds Solder Balls

A stencil reballing job follows a fixed order. You remove the old solder from the IC pads, clean them, and hold the IC steady. Then you lay the RF2 mesh over the IC, line up every aperture with its pad, and press solder tin through the holes. A controlled pass of heat melts the tin into a ball on each pad. Amaoe builds this template from steel mesh with a deformation-resistant material, so the sheet resists bending while you handle it. The square round holes and precise pin location help each ball land on its own pad. Because the template follows the IC footprint, you skip the slow work of placing single balls by hand. You also get a consistent ball array on every amplifier IC you reball, which makes inspection under the microscope faster.

Where It Fits in an RF Section Repair

RF power amplifier ICs sit in the signal path of the phone, so a hardware fault in this area often shows up as a network issue. When your diagnosis points to the amplifier IC, you lift it with a hot air station, clean the pads with a soldering station, and inspect them under a microscope. The stencil comes in at the reballing step, right before you place the IC back on the board. A PCB holder keeps the board steady during heating, and a multimeter helps you test the section after reassembly. If your bench already stocks reballing kits, solder paste and flux, the Amaoe RF2 BGA stencil adds the RF-specific template your workflow was missing. It also pairs with the other Amaoe templates for CPU, memory and power ICs, so you can standardize your reballing process around one brand.

Buying the Right Variant for Your Bench

Amaoe lists RF1 and RF2 as selectable options on one product, and the available information does not map each part number to one variant. Treat the part numbers as the series scope, then confirm the footprint of your own amplifier IC before you order. A shop that handles RF-section jobs regularly can order both variants and cover more boards. Mechanicpk publishes only verified details, so you see what the manufacturer confirms and nothing invented. That precision saves you from ordering the wrong template and losing a day on a job that is already waiting on your bench.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • Steel mesh reballing template for RF power amplifier ICs
  • Deformation-resistant material
  • Precise pin location
  • Square round hole apertures
  • RF1 and RF2 variants under one listing
  • Series covers part numbers 77031, QPM5677, 53735 and 78191-11
  • Works with solder tin, hot air station and soldering station workflow
  • Brand new

Specifications

BrandAmaoe
ModelRF2 (RF1/RF2 series)
CategoryBGA Reballing Stencil
CompatibilityRF power amplifier ICs (77031, QPM5677, 53735, 78191-11)
TechnologyBGA reballing, steel mesh tin planting
MaterialSteel mesh, deformation-resistant
ConditionBrand new

Common Repair Uses

  • Reballing RF power amplifier ICs during RF-section repair
  • Reballing an RF power amplifier IC after removal
  • Rebuilding solder balls during IC change karna on the RF section
  • Repairing hardware fault cases traced to the RF power amplifier IC
  • Repairing network issue cases where the amplifier IC needs reballing
  • Restoring a clean ball array after pad cleaning
  • Tin planting through the stencil apertures with heat

Compatible Devices

  • RF power amplifier ICs listed under the Amaoe RF1/RF2 series
  • 77031 power amplifier IC
  • QPM5677 power amplifier IC
  • 53735 power amplifier IC
  • 78191-11 power amplifier IC

FAQ

What is the product name?
The product name is Amaoe RF2 BGA Stencil.
What is the brand of this product?
The brand of this product is Amaoe.
What is the model of this product?
The model of this product is RF2, part of the Amaoe RF1/RF2 series.
What is this product used for?
This product is used for reballing RF power amplifier ICs with a steel mesh BGA stencil.
Which devices are compatible with this product?
This product is compatible with RF power amplifier ICs listed under the Amaoe RF1/RF2 series, including 77031, QPM5677, 53735 and 78191-11.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which IC part numbers does the Amaoe RF2 stencil cover?
Amaoe lists the RF1 and RF2 series for power amplifier ICs 77031, QPM5677, 53735 and 78191-11. The listing does not map each part number to one variant, so check your IC's pad layout against RF2 before you order.
Can I use the RF2 stencil to reball a CPU or eMMC chip?
No. This stencil targets RF power amplifier ICs. CPU, eMMC and UFS reballing need stencils made for those footprints.