BS-01 Double Ended Brush (2 Pcs) for Mobile PCB Cleaning
₨ 650
BS-01 Double Ended Brush Pack
The BS-01 double ended brush pack gives you two brushes with a working end on both sides, so four ends sit ready on your repair bench. Use it to lift flux residue, dust, and debris from mobile motherboards before inspection, reflow, or reballing. Dedicate one end to wet cleaning with isopropyl alcohol and keep the other end dry for final dusting. Mechanicpk supplies the BS-01 to technicians and service centers across Pakistan who treat board cleaning as a defined step in every hardware fault repair, from charging issue jobs to dead phone diagnosis.
In stock
BS-01 Double Ended Brush for Board-Level Cleaning
The BS-01 double ended brush gives you two working ends on every handle, and the pack includes two brushes, so four ends sit ready on your bench. Board-level mobile repair produces residue constantly: flux after IC reflow, dust under shield cans, and sticky deposits around connectors. A dedicated cleaning brush removes that residue before you inspect, test, or reflow the area again. Mechanicpk supplies the BS-01 for technicians who treat cleaning as a defined step in the repair process, not an afterthought.
Where Cleaning Fits in the PCB Repair Process
Flux residue marks where the last repair happened, and it also hides what you need to see next. After you lift an IC with your hot air station and clean the pads with your soldering station, a film of flux stays around the footprint. That film traps dust, and under a microscope it blurs cold joints, hairline cracks, and corroded pads. On a dead phone, a charging issue, or a hang on logo case, you inspect the board before you commit to another reflow. The BS-01 handles that preparation step. You wet the area with isopropyl alcohol, work the brush across the board in short strokes, and lift the residue so the next inspection shows the actual solder joints instead of leftovers. Pakistani repair shops handle many water-damaged and previously repaired boards, and those arrive with the heaviest residue. Cleaning them before diagnostics saves you from chasing false readings caused by conductive grime between pins. Reballing prep follows the same logic: a residue-free pad area gives your reballing kit stencil a flat surface to sit on.
Two Ends, Two Jobs in One Hand
A double ended brush changes how you organise your cleaning routine. Use one end for wet work with isopropyl alcohol and keep the other end dry for dusting shield areas, connector housings, and charging port cavities after you open the phone. That separation stops you from dragging dissolved flux back across a board you just cleaned. Each BS-01 handle gives you both ends in one hand, so you switch from wet scrubbing to dry dusting without reaching for a second tool or setting the board down. For jumper lagana work, clear the area around the test points first so your probe lands on metal, not residue. The same routine applies to Android boards from Samsung, Oppo, Vivo, Infinix, and Tecno, and to iPhone logic boards, and the speed adds up across a full day of jobs. Test the brush on a low-risk area first when you work near small capacitors or fine-pitch connectors, and keep your ESD mat and wrist strap in place, as you do for every board-level job.
Why a Pack of Two Matters on a Busy Bench
The BS-01 ships as a pack of two brushes, which gives you four working ends. Assign one brush to flux and IPA work and keep the second clean for final dusting before you close the device. A brush that scrubs flux all day picks up residue and loses its finishing value, so a second brush protects that last step. Technicians who run IC change karna jobs daily also use the second brush to sweep stray solder balls and debris off the board after reflow, before power-on. Workshops with two or more technicians split the pair between benches and avoid sharing a contaminated tool. Build your cleaning station around the BS-01 and add the tools that sit next to it in the workflow: PCB holders to fix the board while you brush, microscopes for inspection after cleaning, multimeters for continuity checks on cleaned pads, and test boxes when the repair moves to the software side. Replace a brush when the working end looks worn or loses its shape, because a worn tip scrubs unevenly and leaves residue in corners.
| Weight | 0.9 kg |
|---|
Key Features
- ✓Two brushes per pack, four working ends in total
- ✓Double ended design for separate wet and dry cleaning
- ✓Handles flux residue, dust, and debris on mobile PCBs
- ✓Fits board-level workflows from inspection to reballing prep
- ✓Works alongside isopropyl alcohol for flux cleaning
- ✓Covers Android and iPhone board cleaning
- ✓Keeps a clean spare brush ready for final dusting
- ✓Suits single-technician benches and multi-bench workshops
Specifications
| Model | BS-01 (supplied as 2 pcs per pack) |
|---|---|
| Category | Mobile Repair Accessories > Cleaning Brushes |
| Compatibility | Universal hand cleaning tool, not device-specific |
| Supported Devices | Mobile phone motherboards and PCBs, general electronics boards |
Common Repair Uses
- ✓Flux, dust, and residue cleaning during board-level mobile repair.
- ✓Flux residue removal after IC change karna
- ✓Cleaning pads before reballing
- ✓Dusting boards before microscope inspection
- ✓Cleaning around connectors and charging port areas
- ✓Prepping boards for hot air reflow
- ✓Sweeping debris off boards after rework
- ✓Cleaning boards on charging issue and dead phone jobs
- ✓Clearing grime from boards with a display problem or network issue
Compatible Devices
- ✓Universal, not device-specific. Use it on any mobile phone board or PCB you can reach by hand.
- ✓Samsung Android motherboards
- ✓Oppo and Vivo motherboards
- ✓Infinix and Tecno motherboards
- ✓Xiaomi and Realme motherboards
- ✓iPhone series logic boards
- ✓Small sub-boards and charging port boards
- ✓Tablet motherboards
- ✓General electronics PCBs



