Mechanic iMini Screwdriver ☆0.8 Pentalobe P2 Precision Bit
₨ 400
Pentalobe P2 Bit for iPhone Bottom Screws
The Mechanic iMini Screwdriver ☆0.8 is a precision pentalobe P2 driver with a 0.8 mm tip, built for the bottom-edge screws on Apple iPhones. Its S2 steel bit seats firmly in small recesses, so you can back out the fastener without rounding it. The magnetic tip holds the screw as you lift it, which keeps fasteners from dropping into the housing. Technicians use it for charging port, battery, and front assembly work where a standard driver is too large or too loose. Pair it with a full precision screwdriver set for coverage of other small-format fasteners.
In stock
The Mechanic iMini Screwdriver ☆0.8 targets one job that comes up constantly in mobile repair: removing pentalobe P2 screws without stripping the recess. These fasteners sit along the bottom edge of many Apple iPhones, and a bit with slight wear or poor tip geometry will chew into the screw head within a few turns. This 0.8 mm five-point star tip seats cleanly, so you can open the housing, reach the charging assembly, or pull a battery without turning a routine service visit into a screw-extraction problem. Your bench will feel the difference on the tenth device of the day as much as on the first. The tip starts with the steel. The iMini bit uses S2 tool steel, a grade known for shock resistance at small diameters, where a thin tip has little room to deform under torque. Good tip retention matters when you engage and release the same fastener many times across a busy shift. Magnetic adsorption is the next practical advantage. The bit holds a tiny screw against its tip as you lift it out of the recess, which keeps the fastener from falling into the board or the frame. Losing a small pentalobe screw inside a phone is a common and expensive mistake on a busy bench, and a magnetic tip removes most of that risk. Keep a magnetic mat beside you so each screw lands in its tray. Where does this driver fit in your workflow? It sits at the start of most disassembly sequences, before any soldering or board-level work begins. A technician typically removes the bottom pentalobe screws first, lifts the front assembly, then moves on to the internal connectors and the logic board. For a shop that performs board-level repair, that first step decides how smoothly the rest of the job runs. Pair the driver with a microscope so you can check the screw head and recess for wear before applying torque, and use a PCB holder to keep the board stable once it is open. For Pakistani service centers handling a mixed inventory of iPhones, this tool fills a narrow but essential slot in the kit. It will not replace a complete precision set, and it does not handle the Phillips or Torx fasteners common in other device families. Keep a dedicated iMini pentalobe driver on the bench for Apple work, and use a broader set for everything else. Many technicians also stock spare precision bits, since the tip is the component that wears first. Handling matters as much as the tip itself. Hold the driver with light, even pressure and let the bit seat fully before turning. Forcing a pentalobe screw at an angle is the fastest way to round the recess, and a rounded recess makes the screw hard to extract even with the correct tool. Work slowly through the first two or three turns, then increase speed only once the screw begins to release. Inspect the bit every few sessions for chipping at the tip, because a damaged bit is the most common cause of stripped screws in the workshop. When you compare precision drivers, focus on tip accuracy and fit rather than handle size. A driver that seats cleanly in a 0.8 mm pentalobe recess will outperform a larger kit with loose tips on Apple work. If you are setting up a new bench for iPhone repair, start with this iMini bit before buying a wider set, then add a precision screwdriver kit as your repair volume grows. Your first purchase should solve your most frequent problem, and for iPhone bottom-edge screws, this tool does exactly that.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Five-point star (pentalobe P2) tip in 0.8 mm for bottom-edge Apple screws
- ✓S2 tool steel bit for durability under repeated engagement
- ✓Magnetic tip holds small screws during removal
- ✓Low-profile tip suited to tight bottom-edge recesses
- ✓Consistent seat reduces the risk of rounding the screw head at low torque
- ✓Supports screen, battery, and charging port service workflows
- ✓Part of the Mechanic iMini precision driver range
- ✓Reduces screw-drop risk during micro-service disassembly
Specifications
| Brand | Mechanic |
|---|---|
| Model | iMini |
| Category | Precision Screwdriver |
| Type | Pentalobe P2 (five-point star) |
| Size | 0.8 mm |
| Technology | Magnetic bit tip |
| Material | S2 tool steel bit |
Common Repair Uses
- ✓Removing bottom pentalobe screws before charging port replacement
- ✓Opening the housing for battery replacement
- ✓Accessing the front assembly before logic board work
- ✓Removing tail plug screws on applicable Apple devices
Compatible Devices
- ✓Apple iPhone models with bottom-edge pentalobe P2 screws
- ✓Apple tail plug screws on applicable iPhone models
- ✓Other Apple devices using pentalobe fasteners,
FAQ
What is the product name?
What is the brand of this product?
What is this product used for?
Who should use this product?
Does this tool fit iPhone tail plug screws?
Can a worn bit strip a pentalobe recess?
Related products
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



