Mechanic PN360 Portable Battery Spot Welder 650A
₨ 9,500 Original price was: ₨ 9,500.₨ 8,000Current price is: ₨ 8,000.
PN360 Dual-Pulse Battery Spot Welder
The Mechanic PN360 portable battery spot welder gives repair technicians 650A maximum output, dual-pulse control and a copper busbar in a 140 x 90 x 25 mm handheld body. You weld nickel strip to phone battery tabs, BMS boards and 18650 or 21700 cells without a bench power supply. A 2.0-inch TFT screen shows live weld settings, 80 power stages let you tune each joint, and a built-in rechargeable cell keeps you cordless. Mechanicpk supplies the PN360 to Pakistani repair shops and service centers that rebuild lithium battery packs in-house instead of outsourcing the job.
In stock
PN360 Portable Battery Spot Welder for Phone and Lithium Pack Repair
The PN360 portable battery spot welder from Mechanic packs 650A peak output, dual-pulse control and a built-in rechargeable cell into a body no bigger than 140 x 90 x 25 mm. You skip the bench power supply and the foot pedal. You connect the welding pen, pick a power stage and weld nickel strip to a battery tab right where the repair happens. Mechanicpk supplies this unit to Pakistani workshops that handle phone battery tab work, BMS board replacement and 18650 or 21700 pack rebuilds. The sections below cover the verified specifications and show where the welder fits in a technician’s daily battery workflow.
Key Technical Highlights
The PN360 runs dual-pulse output, which splits each weld into two pulses and keeps the heat impact on thin strip lower than a single burst would. A copper busbar carries current from the power core to the pen, so less energy drops out before it reaches the weld point. You adjust output across 1 to 80 power stages, which gives you fine control when you switch between nickel-plated sheet and pure nickel strip. The rated welding thickness runs from 0.1 mm to 0.2 mm, so you match your strip to that range before you press the pen down. A 2.0-inch HD TFT colour screen shows the live weld parameters. You read your setting instead of guessing it, and you repeat a good weld on the next joint.
Power Source and Portability
A built-in 4000mAh high-rate (70C) cell powers the welder, so you work cordless at the bench, at the counter or on a customer visit. You recharge through the Type-C port, which takes 5V/2.1A at maximum, so a standard phone charger or power bank refills the unit. Maximum output voltage reaches 4.2V and maximum output current reaches 650A. Treat those figures as limits for planning: stay inside the 0.1 to 0.2 mm strip range and let the power stage set the weld strength instead of pressing harder. At 140 x 90 x 25 mm, the PN360 slips into a tool bag beside your multimeter and tweezers. Charge it fully before a long session so every weld in a pack gets the same output.
Where the PN360 Fits in Your Repair Workflow
Battery repair starts with diagnosis. You measure the pack with a multimeter, find the dead cell or the failed protection board, then decide whether the job needs a weld. The PN360 handles that welding step. You tack fresh nickel strip onto replacement cells, reattach a BMS board or fix a lifted tab on a phone battery. Put the joint under a microscope afterwards and check for an even, clean weld spot before you close the pack. Flex and board-side joints that need solder instead of a weld belong on a soldering station, and a PCB holder keeps the work steady while the pen stays in your hand. Two trigger options, automatic and manual, let you choose contact-triggered welds for repeat work or deliberate single welds on awkward tabs. Workshops that outgrow handheld welding for high-volume pack building can step up to a bench-mounted, foot-pedal spot welder in the same category.
Why Technicians Choose This Tool
Pakistani repair benches see the same battery faults every week: dead battery, charging issue after a poor cell swap, and hardware fault on power bank, e-bike and laptop packs. Without a spot welder, those jobs leave your shop for an outside battery pack maker. With the PN360, you finish them at your own bench and keep the margin. The unit suits mobile repair technicians, small battery pack builders and service centers that want one portable welder for phone battery tabs and cylindrical cell packs. The dual-pulse output, copper busbar and visible power stage give you a repeatable process, which matters when customers bring the same pack type back for a second repair. Order the PN360 from Mechanicpk and weld your next battery tab at the bench instead of sending it out.
| Weight | 0.35 kg |
|---|
Key Features
- ✓Dual-pulse welding output for lower heat impact on thin strip
- ✓Copper busbar current conduction for efficient power delivery
- ✓Maximum output current of 650A
- ✓1–80 adjustable power stages
- ✓2.0-inch HD TFT colour display showing live weld parameters
- ✓Automatic and manual trigger modes
- ✓Built-in 4000mAh high-rate (70C) rechargeable cell for cordless use
- ✓Type-C charging and a compact 140 x 90 x 25 mm body
Specifications
| Brand | Mechanic |
|---|---|
| Model | PN360 |
| Category | Portable Dual-Pulse Battery Spot Welder |
| Compatibility | 18650 and 21700 cells, mobile phone battery tabs, BMS boards, nickel strip and nickel-plated sheet (0.1 mm – 0.2 mm) |
| Supported Devices | Universal — not phone-model-specific |
| Technology | Copper busbar current conduction with dual-pulse output, 2.0-inch HD TFT colour display, 1–80 adjustable power stages, automatic and manual trigger modes, built-in 4000mAh 70C rechargeable cell |
| Input Voltage | 5V/2.1A (Max), Type-C charging port |
| Output Voltage | 4.2V (Max) |
| Dimensions | 140 x 90 x 25 mm |
Common Repair Uses
- ✓Battery tab and pack repair work on the technician’s bench
- ✓Mobile phone battery spot welding
- ✓Lithium battery nickel plate spot welding
- ✓Battery cell replacement in damaged packs
- ✓Reattaching BMS boards to cell packs
- ✓Rebuilding 18650 and 21700 battery packs
- ✓Repairing power bank battery packs
- ✓Repairing e-bike and laptop battery packs
- ✓DIY battery pack assembly
Compatible Devices
- ✓Universal — works on battery tabs and nickel strip within 0.1–0.2 mm thickness, not tied to specific phone models
- ✓Mobile phone battery tabs
- ✓18650 lithium cell packs
- ✓21700 lithium cell packs
- ✓Power bank battery packs
- ✓E-bike battery packs
- ✓Laptop battery packs
- ✓BMS (protection) boards
- ✓Nickel strip and nickel-plated sheet, 0.1–0.2 mm
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What nickel strip thickness can the PN360 weld?
Does the PN360 need mains power while welding?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



