MT6637XP WiFi Bluetooth GPS Combo IC for Mobile Repair
₨ 550
MT6637XP WiFi Bluetooth GPS IC for Board-Level Connectivity Repair
The MT6637XP is a MediaTek combo IC that handles WiFi, Bluetooth and GNSS location on mobile phone boards. Technicians reach for it when a device shows no WiFi networks, drops Bluetooth pairings or never locks a GPS fix. Replacing it is board-level work that needs a hot air station, quality flux and reballing before reflow. Confirm the connectivity fault and the board model before you order. For workshops handling MediaTek-based phones, it is a practical part to keep on the shelf.
MT6637XP WiFi Bluetooth GPS IC: Connectivity Repair Guide
The MT6637XP WiFi Bluetooth GPS IC is a MediaTek connectivity chip that covers WiFi, Bluetooth and GNSS location from one package. You meet it most often on boards where a phone shows no WiFi networks, drops Bluetooth connections or cannot lock a GPS fix. Its position in the RF section beside the processor means a fault here can look like an antenna or software issue until you test properly. For a repair bench, the IC is worth stocking when you can confirm the fault and carry out a clean board-level swap. Work through the sections below before you pull the chip.
Where This Connectivity IC Fits in the Signal Path
Inside the phone, the WiFi, Bluetooth and GNSS blocks share a link with the application processor and the antenna matching network. The processor sends control data to the connectivity chip over internal interfaces, and the chip turns that data into radio signals for each protocol. TechInsights describes the MT6637 family as multi-protocol RF transceivers built for smartphones, which fits this role. On the bench, a dead radio can originate in the chip, in the power rails feeding it, or in the antenna path. Treat the IC as one node in that chain rather than the only suspect. Once you know where the chain breaks, the repair decision becomes much clearer. Pair this part with reballing kits and a hot air station from our repair tools range for a complete workflow.
Diagnosing a Mobile Phone Connectivity IC Fault
Start with the symptoms that point to the radio block: no WiFi networks in range, random Bluetooth disconnects, or GPS that never locks. Check the antenna contacts and their continuity before anything else, because a damaged antenna contact can mimic a dead IC. Next, measure the supply rails feeding the chip and compare them with a healthy board of the same model. Liquid contact, board flex and thermal stress around the connectivity zone are the usual causes of failure. Replace the IC only after these checks clear the surrounding parts, since an unnecessary swap costs stock and turnaround time. A structured diagnosis saves the customer’s time and protects your margin on the job.
Rework Steps for the MT6637XP WiFi Bluetooth GPS IC
This is a board-level job, not a plug-and-play swap. The chip sits in a dense RF section, so use a hot air station with accurate temperature control, a preheat step and quality flux. Remove the old IC, clean the pads fully and check for lifted or damaged copper before you reball. Ball size and alignment decide whether the new connection holds, and misaligned balls usually show up as intermittent WiFi or a dead radio after reflow. Work under a microscope and keep the bench static-safe, because excess heat or a static discharge can crack the die or lift pads. Finish with a full functional test of WiFi, Bluetooth and GPS before the board goes back into the device.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Combines WiFi, Bluetooth and GPS/GNSS functions in one IC
- ✓Listed as a MediaTek connectivity part for Dimensity-platform boards
- ✓Targets no-WiFi, Bluetooth pairing and GPS lock faults
- ✓Suited to board-level rework with hot air and reballing
- ✓Works alongside application processors and RF front-end parts on the board
- ✓Supports a durable reinstall when reballed correctly
- ✓Common replacement candidate after liquid damage or drop-related faults
- ✓Practical stock item for technicians handling MediaTek-based repairs
Specifications
| Brand | MediaTek |
|---|---|
| Model | MT6637XP |
| Category | Mobile Phone ICs |
| Technology | WiFi, Bluetooth and GNSS combo IC |
| Compatibility | MediaTek Dimensity-platform boards (chipset-family scope, per store listing; verify your board before ordering) |
Common Repair Uses
- ✓No WiFi networks detected on the device
- ✓WiFi drops or weak signal
- ✓Bluetooth not turning on or pairing failures
- ✓GPS not locking or inaccurate location
- ✓Connectivity faults after liquid damage or board flex
- ✓IC reflow and replacement during board-level repair
Compatible Devices
- ✓Chipset-family scope only. Device-level compatibility is not independently verified.
- ✓MediaTek Dimensity-platform boards (chipset-family scope)
- ✓Oppo K10 (PGJM10), as cited on the store listing; not independently checked
- ✓Any other board: verify the chip’s marking and footprint against the donor board before installing
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does the MT6637XP handle WiFi, Bluetooth and GPS in one chip?
What symptoms point to a failed MT6637XP?
Related products
343S0694 Touch IC U2402 iPhone 6 and 6 Plus Touch Black IC
In stock
U2 Charging iPhone 8, iPhone 8 Plus, iPhone X Chip – 1612A1
In stock



