Mechanic iMini Series Y Shape 0.6 Soldering Tip
₨ 400
Mechanic iMini Series Y Shape 0.6 Soldering Tip for Fine-Pitch Mobile Repair
The Mechanic iMini Series Y Shape 0.6 Soldering Tip gives you a 0.6mm Y-shaped working end for tight spaces on mobile motherboards. You can reach small ICs, connector pins, and crowded pads where a conical tip cannot sit cleanly. It is made for Mechanic iMini series soldering stations and suits jumper wire runs, lifted pad touch-up, and charging port or battery connector repairs. Order from KB GSM Store with fast delivery across Pakistan and keep your board-level repair work moving.
In stock
Mobile phone motherboards pack more components into less space with every generation, and the Mechanic iMini Series Y Shape 0.6 Soldering Tip is built for that problem. This replacement tip has a 0.6mm Y-shaped working end that reaches into narrow gaps around connectors, small ICs, and closely spaced pads. Technicians handling dead phone boards, charging issue repairs, or display problem diagnostics often need a tip that works one joint without disturbing the parts beside it. The Y profile gives you a more controlled contact point, so you can position the tip on a pin while keeping heat away from neighboring components. You get precise soldering on fine-pitch boards without switching to a larger tip mid-repair. Jumper wire work is one of the most common uses for this shape. After you prepare a damaged trace and route a new wire, you need a tip that lays solder cleanly on a thin path. A wide or flat tip makes it easy to bridge two traces, while a fine Y-shaped point lets you tack the wire down with less risk. Connector pin resoldering follows the same logic. Charging ports and battery connectors have pins packed close together, and a slight overlap of solder between them can turn a simple fix into a larger fault. Working with this 0.6mm tip gives you the control to melt one pin, release it, and move on. Lifted pad touch-up is another practical task for this tip. When a pad lifts during removal or after heavy handling, you clean the surface, apply flux, and tin the pad with minimal heat. The shape of the Y tip lets you reach the pad from an angle, which keeps the iron away from the surrounding solder mask and nearby components. Camera module boards and fine-pitch sockets also benefit from this kind of access. Heat management matters just as much as shape. A tip that transfers heat efficiently lets you finish a joint quickly, which reduces the time a pad spends at high temperature. Keeping dwell time short protects both the pad and the component next to it. Clean the tip regularly with a brass sponge or wet sponge, and tin it before each use so heat transfers evenly across the working face. These habits extend tip life and keep joint quality consistent across a full day of repairs. Compatibility is the first thing to check before you buy. This tip is made for Mechanic iMini series soldering stations, so confirm your iron model and tip-mount type before you order. Technicians using other soldering station brands or older station models should verify fit first, because tip mounts differ even within the same manufacturer’s range. Once you confirm compatibility, the tip fits into a standard mobile motherboard repair workflow at the component soldering stage. It works after you have diagnosed the fault and prepared the board. It is not a chip removal tool and it is not designed for large joints or bulk soldering. Use it to finish the job you have already planned, and reserve heavier tips for bigger work. For a repair shop stocking its soldering bench, this tip earns a place beside a conical and a chisel tip. Each shape covers different repair scenarios, and having the right one ready saves time that would otherwise go into repositioning the iron. Order the Mechanic iMini Series Y Shape 0.6 Soldering Tip from KB GSM Store and add a precision option to your iMini station.
| Weight | 0.11 kg |
|---|
Key Features
- ✓Y-shaped tip design for soldering around tightly packed components
- ✓0.6mm working size for fine-pitch, component-level work
- ✓Made for Mechanic iMini series soldering stations
- ✓Efficient heat transfer for fast, controlled joints
- ✓Reaches narrow spaces near connectors and small ICs
- ✓Suited to jumper wire and connector pin soldering
- ✓Supports precision touch-up on lifted pads
- ✓Fits standard mobile motherboard repair workflows
Specifications
| Brand Entity | Mechanic |
|---|---|
| Product Entity | iMini Series Y Shape 0.6 Soldering Tip |
| Technology Entity | Y-shape precision soldering tip |
| Compatible Device Entities | Mechanic iMini series soldering stations, mobile phone motherboards |
| Repair Process Entity | Component soldering, jumper wire repair, connector pin resoldering, pad touch-up |
| Industry Entity | Mobile phone motherboard repair, PCB rework |
Common Repair Uses
- ✓Fine-pitch SMD component soldering
- ✓Jumper wire installation after trace repair
- ✓Connector pin resoldering on charging ports
- ✓Lifted pad touch-up on motherboards
- ✓Battery connector repair
- ✓Camera module board repair
- ✓Precision board-level rework on crowded boards
Compatible Devices
- ✓Mechanic iMini series soldering stations
- ✓Mobile phone motherboards
- ✓Smartphone charging port and battery connector boards
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is the 0.6mm Y shape suitable for BGA or large joint soldering?
Will this tip fit soldering stations other than the iMini series?
Related products
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



