0.6mm Curved Nozzle for 2008 Series Heatgun
₨ 850
0.6mm Curved Nozzle for 2008 Heat Gun
The 0.6mm curved nozzle gives your 2008 series hot air gun an angled tip for precise board-level rework. You fit it onto the handle of a 2008 series station and aim heat at one small spot on a mobile mainboard. The curve keeps the handle out of your line of sight, so you can work comfortably under a microscope. It suits IC removal, connector reflow and small SMD rework in repair shops across Pakistan. Mechanicpk supplies it for technicians who need a dependable replacement or an extra nozzle for the bench.
In stock
Precision Rework with the 0.6mm Curved Nozzle for 2008 Series Heat Guns
The 0.6mm curved nozzle for 2008 series heat guns gives you a narrow, angled hot air outlet for board-level mobile repair. You attach it to the hot air handle, aim the airflow at a single component, and keep the heat away from the parts around it. Technicians who work under a microscope prefer curved nozzles because the bend moves the handle out of the line of sight. If your bench already runs a 2008 series station, this nozzle adds a focused tip for tight areas on dense mobile PCBs.
Station Compatibility and Fit
This nozzle targets the 2008 series hot air gun. Supplier listings for 2008 series curved nozzles name the 858A, 858D, 858AD, 2008 and 705 series stations as compatible. Check your station label before you order. Nozzles built for other families do not interchange, and 861 series nozzles do not fit a 2008 series handle.
Fit matters because a loose nozzle leaks hot air at the joint. That leak wastes heat and warms the area around your target component. A nozzle matched to the 2008 series handle keeps the airflow where you aim it. You also avoid the slow trial-and-error of forcing the wrong nozzle onto the wrong handle.
Where the Curved Nozzle Fits in Your Repair Workflow
Hot air rework sits at the centre of mobile PCB repair, and nozzle shape controls how well you place that heat. A straight nozzle works when you hold the handle upright over the board. A curved nozzle works better when a microscope, a PCB holder or a crowded bench limits your angle. The bend lets you reach shielding cans, small ICs and connectors without blocking the view of the joint you work on.
You use the nozzle during IC change karna jobs on dead phone boards, charging port area repair, and connector reflow. For dead after flash or hang on logo faults that trace back to hardware, you often reflow or replace a small chip near other sensitive parts. A narrow, angled airflow helps you heat the target while you protect the neighbours. Pair it with flux, a PCB holder and your microscope for a steadier process, and check results with a multimeter after each rework step. When you move up to BGA work, add a reballing kit to the same bench.
Heat Handling and Bench Practice
Always switch the station to cool-down before you remove or swap a nozzle. The metal tip stays hot well after you release the trigger or stand the handle. Seat the nozzle fully on the handle so it does not wobble during use. Keep the tip clean, because flux residue and dust restrict airflow and shift your heat pattern.
Hold the handle at a steady distance and move the nozzle in a small circle over the component rather than fixing it on one spot. This spreads heat across the joint and lowers the risk of lifting pads. Start with a lower temperature and raise it only as the solder requires, especially around plastic connectors and display flex sockets. Keep a spare nozzle on the bench so a damaged tip never stops a job.
Mechanicpk stocks this curved nozzle alongside hot air stations and soldering stations, so you can build a complete rework setup from one supplier.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Curved tip that keeps the handle out of your view
- ✓Fits 2008 series hot air gun handles
- ✓Narrow 0.6mm tip size for focused airflow
- ✓Reaches tight areas between components on dense PCBs
- ✓Works with microscope-based rework setups
- ✓Suits IC removal, reflow and connector repair
- ✓Works with 858A, 858D, 858AD, 2008 and 705 series stations
- ✓Replaces a worn or damaged nozzle on your bench
Specifications
| Model | 0.6mm Curved Nozzle |
|---|---|
| Category | Hot Air Gun Nozzles |
| Compatibility | 2008 series hot air gun (858A, 858D, 858AD, 2008, 705 series stations) |
| Technology | Curved hot air rework nozzle |
Common Repair Uses
- ✓Board-level hot air rework on mobile phone PCBs
- ✓SMD IC removal and replacement
- ✓Shielding can removal
- ✓Charging IC area rework
- ✓Connector and FPC socket reflow
- ✓Small passive component desoldering
- ✓Rework under a microscope with limited handle angle
- ✓Dead phone board hardware fault repair
- ✓Localised board preheating before component removal
Compatible Devices
- ✓Station-compatible nozzle for 2008 series hot air guns; the nozzle is device-agnostic and works on mobile mainboards of any brand
- ✓2008 series hot air gun
- ✓858A hot air station
- ✓858D hot air station
- ✓858AD hot air station
- ✓Quick 2008 hot air station
- ✓705 series hot air station
- ✓Android mobile phone mainboards (Samsung, Oppo, Vivo, Infinix, Tecno)
- ✓iPhone series mainboards
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does this nozzle fit the 861 series hot air gun?
Why should I use a curved nozzle instead of a straight one under a microscope?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



