RF4 HX-50 Solder Flux 50g – BGA Reballing Flux Paste

₨ 1

RF4 HX-50 Flux Paste for SMT and BGA Work

The RF4 HX-50 solder flux packs 50g of lead-free flux paste for chip-level mobile repair. You use it on SMT soldering and BGA reballing, the two jobs where oxide on a pad ruins a joint before the solder even melts. Apply a thin layer with a brush or needle tip, bring in your hot air station or soldering iron, and the solder wets the pad cleanly. The 50g jar covers daily IC change karna work on charging, display, and power sections. It suits benches that handle dead phone and hardware fault cases every week. Mechanicpk delivers the RF4 HX-50 across Pakistan.

Out of stock

17 People watching this product now!
Description

Lead-Free BGA Reballing Flux Paste for Chip-Level Mobile Repair

The RF4 HX-50 solder flux gives your bench a 50g flux paste built for SMT soldering and BGA reballing on mobile phone boards. Flux does one job before solder touches a pad: it strips oxide so molten alloy wets the copper and flows into a sound joint. Skip it, and you chase cold joints, bridged balls, and boards that come back a week later with the same charging issue. RF4 supplies the HX-50 as a lead-free paste, so you place it exactly where the joint needs it with a brush, a needle, or a clean tip. Mechanicpk stocks it for Pakistani workshops that run IC change, reballing, and trace repair every day.

Where HX-50 Fits in Your Rework Workflow

Every board-level job starts with heat, and flux decides how well that heat turns into a good joint. When you lift a BGA chip with your hot air station, you clean the pads, then coat them with a thin, even layer of paste. When you reball, you spread the paste over the cleaned pads before the stencil goes down, so the balls melt and seat on bare, active copper. When you drop a replacement IC onto the board, fresh flux under and around it helps the solder pull into each pad instead of balling up on one side.

The same paste handles smaller SMT work. Tin a lifted pad, repair a broken trace with a jumper lagana job, or refit a charging connector, and you get predictable wetting from the first pass. Pair it with a quality soldering station for iron work, a hot air station for chip removal, and a microscope for pad inspection, and you control every step from removal to final check.

Technical Profile and Handling at the Bench

RF4 sells the HX-50 as a lead-free solder flux paste in a 50g pack. The paste form gives you control that liquid flux cannot match on a vertical or crowded board, because it stays where you put it. Work with a thin layer: excess paste only adds smoke and mess around neighboring components. Keep the lid closed between jobs, and use a PCB holder to hold the board steady while you apply and heat.

After you finish a repair, inspect the joints under magnification and test continuity with your multimeter before you power the board. A clean joint with a smooth, bright fillet tells you the flux and heat profile matched. If a board still shows a dead phone symptom or hangs on logo after rework, the flux was not the fault; trace the power rails and recheck the chip seating.

Why Technicians Stock the HX-50 Jar

Reballing, IC change, and connector replacement burn through flux faster than most buyers expect. A 50g jar covers a full week of high-volume bench work without constant reordering, which matters for shops that run several technicians on one counter. RF4 positions the HX-50 within its soldering range alongside its rework stations and microscopes, so you keep your consumables and equipment under one brand family. If you build your bench around reballing kits, hot air stations, and soldering stations, the HX-50 gives that setup the flux it needs to deliver reliable joints.

Additional information
Weight0.50 kg
Q & A
Please login to post questions

Key Features

  • 50g jar pack
  • Lead-free flux paste formulation
  • Built for SMT soldering
  • Built for BGA reballing
  • Designed for mobile phone PCB repair
  • Paste form for controlled brush or needle application
  • Flux action that helps solder wet clean pads
  • RF4 HX-50 model for consistent reordering

Specifications

BrandRF4
ModelHX-50
CategorySoldering Paste & Flux
CompatibilitySMT soldering and BGA reballing on mobile phone PCBs
TechnologyLead-free solder flux paste
Weight50g

Common Repair Uses

  • Chip-level soldering and reballing on mobile phone boards
  • BGA reballing
  • IC change karna after hot air removal
  • Pad tinning on lifted or cleaned pads
  • Charging IC replacement for charging issue faults
  • Jumper lagana on broken traces
  • Connector soldering (charging, display, battery)
  • SMT component refitting
  • Board rework on dead phone and hardware fault cases

Compatible Devices

  • Universal — not device-specific; works as a soldering flux on mobile phone PCBs for SMT and BGA joints
  • Android smartphone motherboards (Samsung, Oppo, Vivo, Infinix, Tecno)
  • iPhone logic boards
  • Tablet motherboards
  • BGA chips on phone PCBs (CPU, eMMC, UFS, RAM)
  • Power management ICs (PMIC)
  • Charging ICs and charging port connectors
  • Display and touch connector pads
  • SMT components on phone PCBs

FAQ

What is the product name?
The product name is RF4 HX-50 Solder Flux (50g).
What is the brand of this product?
The brand of this product is RF4.
What is the model of this product?
The model of this product is HX-50.
What is this product used for?
This product is used for SMT soldering and BGA reballing on mobile phone PCBs.
Which devices are compatible with this product?
This product is compatible with mobile phone PCBs in general. It is a universal soldering flux, not tied to specific device models.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Is RF4 HX-50 flux lead-free?
Yes. RF4 lists the HX-50 as a lead-free solder flux paste.
Can I use RF4 HX-50 flux for BGA reballing on mobile boards?
Yes. The HX-50 is listed for SMT soldering and BGA reballing, so you can use it when you remove, reball, and refit BGA chips on mobile phone PCBs.