Mechanic SU7 Green UV Solder Mask Ink 10ml for PCB Repair
₨ 350
Mechanic SU7 Green UV Masking Paste
Mechanic SU7 UV solder mask ink restores the insulating green layer on a motherboard after micro-soldering. You apply a thin coat over a jumper wire, a repaired trace or exposed copper, then cure it under UV light or sunlight. The 10ml tube suits repair shops that handle daily charging issue, dead phone and pad repair jobs. Green colour keeps your coverage visible under the microscope, and the instant-curing formula cuts waiting time on the bench. Add it beside your soldering station and hot air station as a standard sealing step after board-level work.
In stock
Mechanic SU7 UV Solder Mask Ink for Board-Level Sealing
Mechanic SU7 UV solder mask ink gives you a fast-curing green insulation layer for the spots where a repair strips the original mask. The 10ml tube sits at the end of the micro-soldering workflow: you finish the jumper, clean the area, and seal the exposed copper before the board goes back into the phone. Repair shops across Pakistan use UV-curable coatings like this to restore the finish on motherboards after trace repair, pad repair and BGA rework. The SU7 variant targets quick turnaround, and Pakistani marketplace listings describe it as a 3-second dry formula.
Technical Highlights of the SU7 Green Formula
SU7 is a UV-curable solder mask ink, so the paste stays liquid and workable until UV light hits it. That gives you time to position the coat precisely, spread it over the target area, and cure only when the coverage looks right. The listed curing methods are UV light and sunlight, which means a UV torch or lamp on the bench does the job, and daylight works as a backup. The green colour matches the mask on many phone boards and shows clearly under a microscope, so you spot thin patches and bare copper before curing. The tube holds 10ml, enough for a large number of small jumper and trace repairs. After curing, the ink forms a solid insulating coating over the exposed copper, which protects the repair from accidental shorts and surface contact.
Where SU7 Fits in Your Repair Workflow
You reach for UV mask ink after the hardware fault is fixed, not before. A typical sequence on a dead phone with a charging issue starts with IC change karna using your hot air station, followed by cleaning the pads with flux remover. Next comes jumper lagana to repair a broken trace, and a continuity check with your multimeter to confirm the connection. Once the jumper tests good, you apply SU7 over the wire and the exposed copper, then cure it under UV. A PCB holder keeps the board steady during application, and a microscope lets you control the coating edge so it stays off nearby pads and connectors. The same step applies after pad repair, after lifting a damaged mask during reballing, and after any rework that scrapes the original green layer. Standard practice for UV mask inks in this range includes wiping off excess uncured ink with a gasoline or oil-base solvent before the final cure.
Why Technicians Stock UV Mask Ink Beside the Soldering Station
Board-level work leaves bare copper behind, and bare copper invites shorts, corrosion and repeat failures. A tube of UV mask ink costs little compared with a returned phone, so shops treat it as a consumable that sits next to the flux and solder wire. SU7 gives you a single-purpose product for one job: insulating and protecting repaired areas on PCBs. It suits both shop owners who run several benches and individual technicians who handle a few boards a day. Pair it with a UV lamp, fine tweezers and jumper wire, and your repair finishes look clean and consistent across every board you return to a customer.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Green UV-curable solder mask ink
- ✓Instant-curing formula marketed as a 3-second dry
- ✓Cures under UV light or sunlight
- ✓10ml tube
- ✓Green colour stays visible under the microscope
- ✓Insulates jumper wires and exposed copper
- ✓Protects PCB repairs and rework areas
- ✓Suits mobile phone and general electronics boards
Specifications
| Brand | Mechanic |
|---|---|
| Model | SU7 |
| Category | UV Solder Mask Ink / Masking Paste |
| Technology | UV curing (UV light or sunlight) |
| Compatibility | Universal PCB repair use, not device-specific |
| Dimensions | 10ml net content |
Common Repair Uses
- ✓Insulating and protecting PCB areas after micro-soldering and rework
- ✓Insulating jumper wires after trace repair
- ✓Sealing exposed copper after pad repair
- ✓Restoring solder mask after BGA rework
- ✓Protecting repaired traces on dead phone boards
- ✓Covering damaged mask after charging IC change
- ✓Replacing scratched or lifted solder mask on motherboards
- ✓Insulating circuit areas against shorts after hardware fault repair
- ✓Finishing board repairs before reassembly
Compatible Devices
- ✓Universal board-level use on PCBs, not limited to specific phone models or brands
- ✓Smartphone motherboards
- ✓iPhone logic boards
- ✓Android phone mainboards
- ✓Computer and laptop PCBs
- ✓Repaired traces with jumper wires
- ✓Exposed copper after pad repair
- ✓Areas where hot air rework removed the original mask
- ✓General electronics circuit boards
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
How do you cure Mechanic SU7 UV solder mask ink?
Can SU7 green mask ink insulate a jumper wire on a motherboard?
Related products
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



