Soldering Iron Stand 218 – Adjustable Carbon Steel Holder
₨ 250
Metal Soldering Iron Stand 218
The Soldering Iron Stand 218 gives your bench a stable parking spot for a hot iron. A carbon steel stand sits on a metal base, and a fixed screw lets you set the holder height to match the iron in your hand. Mobile repair technicians use this soldering iron stand for mobile repair work to keep the tip off the board, the cables, and the table surface between joints. The desktop base stays put while you switch to tweezers, flux, or a multimeter probe. Whether you work on charging ports, jumper tracks, or IC pads, you get a safer place to rest the iron without reaching for makeshift supports.
In stock
Soldering Iron Stand for Mobile Repair Benches: Model 218 Overview
The Soldering Iron Stand 218 gives a hot iron a fixed home on your repair bench. As a soldering iron stand for mobile repair work, it pairs a carbon steel stand with a metal base, so the iron stays clear of the PCB, the power cables, and the work surface while you handle the next step. Every GSM technician knows the cost of a dropped iron: a burnt mat, a damaged flex, or a motherboard with a new hardware fault. A dedicated holder removes that risk at a very small cost compared with the rest of your bench setup.
Construction and Technical Highlights
The stand uses carbon steel for the upright and a metal base for stability. The base measures approximately 120 x 70 x 16 mm, which gives it a wide, low footprint that resists tipping on a crowded desktop. A fixed screw locks the holder in position, and the adjustable height lets you set the iron at the angle and level that suit your reach. This adjustable soldering iron stand design matters when you swap between irons of different handle sizes on the same bench. Metal construction also tolerates the heat of high-temperature tips, which is the core requirement for any holder you place next to a working iron.
Assembly stays simple. You fit the parts, tighten the screw, and the stand sits ready on the desktop. No power connection, no calibration, and no software are involved, so the stand never competes with your programmer, test box, or hot air station for sockets or attention.
Where It Fits in Your Repair Workflow
Board-level repair involves constant pick-up and put-down cycles. You tin a pad, check continuity with your multimeter, clean the area, and return to the iron. Each cycle needs a safe rest position. On a typical job, such as charging port replacement, jumper lagana on a damaged track, or IC change karna on a dead phone, you set the iron in the stand, work with tweezers or a microscope, and pick the iron up again within seconds.
The stand pairs naturally with the rest of a soldering setup. Technicians who run a soldering station and a hot air station side by side keep the iron in this stand while the hot air gun does the heavy lifting on BGA parts. Reballing kits, PCB holders, and a microscope all share the same bench, so a compact holder that does not demand extra space helps you keep the layout tidy. If your workflow grows, a soldering station with a built-in holder is the logical next step, and this stand continues to serve as a spare rest point for a secondary iron.
Why Technicians Stock Model 218
Repair shops, service centers, and training labs all need the same basic safety layer around a soldering iron. Model 218 covers it with metal construction, an adjustable holder, and a stable desktop base. You can place several stands across a multi-technician shop or a classroom without a large budget commitment. The stand suits standard soldering irons, so you do not need to match it to one specific brand or model of iron.
For Pakistani repair benches, where tables often hold phones, trays, screws, and chargers within arm’s reach, a fixed holder protects both the technician and the customer’s device. Place it on your dominant-hand side, set the height with the screw, and you build a repeatable habit: every pause in soldering ends with the iron in the stand. That habit prevents burns, protects boards that already carry a hardware fault, and keeps your workspace ready for the next job.
| Weight | 0.15 kg |
|---|
Key Features
- ✓Carbon steel stand for sturdy iron support
- ✓Metal base for desktop stability
- ✓Adjustable height for different irons
- ✓Fixed screw to lock the holder in place
- ✓Suitable for high-temperature soldering tips
- ✓Dual-protection design that guards against accidental contact with the iron
- ✓Fits standard soldering irons
- ✓Simple assembly with no tools beyond the fixed screw
Specifications
| Model | 218 |
|---|---|
| Category | Soldering Accessories |
| Compatibility | Standard soldering irons |
| Material | Carbon steel (metal stand and metal base) |
| Dimensions | Base approx. 120 x 70 x 16 mm (L x W x H) |
Common Repair Uses
- ✓Resting a hot iron safely between soldering steps during electronics and mobile board repair.
- ✓Parking the iron between solder joints
- ✓Charging port replacement sessions
- ✓Jumper lagana on damaged motherboard tracks
- ✓IC change karna and pad cleaning
- ✓Board-level hardware fault repair
- ✓PCB assembly and repair work
- ✓Holding the iron while you pick up tweezers or flux
- ✓Training and practice soldering in labs
Compatible Devices
- ✓Universal — not device-specific. The stand holds standard soldering irons and does not depend on any phone brand, model, or chipset.
- ✓Standard soldering irons
- ✓Desktop mobile repair benches
- ✓Mobile repair workshops
- ✓Electronics repair benches
- ✓PCB assembly and repair stations
- ✓Educational electronics labs
- ✓DIY electronics setups
- ✓Professional repair workshops
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is the Soldering Iron Stand 218 adjustable for different soldering irons?
What are the base size and material of the Soldering Iron Stand 218?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock



