Aifen A902 Dual Soldering Station 2 Handles 6 Tips

₨ 35,000

Dual-Channel 350W Station for Board Repair

The Aifen A902 dual soldering station packs two independent heating channels into a single 350W unit. This kit ships with a C210 handle, a C245 handle, and six tips (three C210, three C245), so you cover fine-pitch IC work and heavy pad work from day one. The temperature range runs from 100°C to 450°C, and you switch between Celsius and Fahrenheit as needed. Each handle works independently, and you can store preset temperatures per station. Mobile repair shops use it for charging IC replacement, connector work, and pad cleaning on smartphone, tablet, and laptop boards.

In stock

14 People watching this product now!
Description

Aifen A902 Dual Soldering Station for Mobile Board-Level Repair

The Aifen A902 dual soldering station gives your bench two independent soldering channels in one 350W unit. You hold a fine-pitch handle in one hand and a heavier handle in the other, and you never swap cartridges mid-job. Mechanicpk supplies this kit with a C210 handle, a C245 handle, and six tips. That pairing covers the two cartridge families technicians reach for most often on logic boards. You replace a charging IC, lift a shielded connector, or clean pads before reballing, and both tools stay heated and ready.

Dual Channel Design Built on C115, C210 and C245 Cartridges

Each handle draws from its own channel, and you shut either one off without touching the other. That control matters on dense boards. A C210 tip handles fine-pitch components near sensitive neighbors, while a C245 tip delivers the thermal mass you need for ground planes and large pads. The station accepts C115, C210, and C245 handles. The T245 handle also takes C470 heating elements, which gives you extra capacity for large joints and heavy solder volume. Because the tips follow the standard C-series cartridge format, you find spare tips in several shapes without hunting for proprietary parts.

Temperature Control You Adjust at the Handle

The station covers 100°C to 450°C (212°F to 842°F) and converts between Celsius and Fahrenheit on demand. You change the set temperature with the buttons on the handle, so your eyes stay on the board and your hand stays on the work. Each station stores memory temperatures: a short press reads a stored value, and a long press saves a new one. Set a lower preset for fine-pitch IC work and a higher one for ground-heavy areas, then jump between them as the repair demands. Three cleaning modes help you keep the tip tinned, and the automatic sleep function protects tips when you step away from the bench.

What the 2 Handle and 6 Tip Kit Includes

This configuration includes the A902 station, one C210 handle, one C245 handle, three C210 tips, and three C245 tips. The split gives you spares for the tip style you wear out fastest and keeps both handles productive from the first repair. Pick this kit if your bench already runs a hot air station and a separate fine-pitch iron, and you want a dual-handle core without paying for a third handle you never use. The A902 also supports a C115 handle for micro-scale work, so you extend the setup later without replacing the station.

Where It Fits in the Mobile Repair and PCB Workflow

The A902 sits in the soldering and rework stage of your board repair process. After diagnostics with a multimeter, you remove a faulty IC or connector with hot air, then clean the pads with the C210 tip and flux. You place the new part and secure it with a handle matched to the joint size. For hardware faults like a charging issue, a display problem, or a dead phone after a short, this workflow repeats constantly. The station also suits jumper wire repairs on broken traces, connector re-tinning, shield can removal, and pad preparation before reballing with a stencil. Pair it with a microscope for fine-pitch work and a PCB holder for stability.

Pairing and Upgrade Path for Your Bench

Beginners who run a single-handle iron gain the biggest jump here, because two channels cut handle-swapping time on every board. Technicians already using a basic soldering station move up to this unit for the independent channels and the wider cartridge range. For a complete board-level setup, add a hot air station for component removal, a reballing kit for BGA work, and a good multimeter for fault tracing. That combination covers testing, removal, cleaning, and re-soldering without leaving your bench.

Additional information
Weight2.5 kg
Q & A
Please login to post questions

Key Features

  • Dual-channel design with independent control of each handle
  • 350W output across both stations
  • Supports C115, C210, and C245 handles
  • T245 handle takes C470 heating elements
  • Temperature range of 100°C to 450°C (212°F to 842°F)
  • Celsius/Fahrenheit conversion
  • Handle button temperature adjustment
  • Memory temperature storage per station with three cleaning modes and automatic sleep

Specifications

BrandAifen
ModelA902
CategorySoldering Station
CompatibilityC115, C210, C245 handles; C470 heating element via T245 handle
TechnologyDual-channel soldering station with C-series cartridge tips
Input VoltageAC 110V/220V, 50-60Hz
Power Rating350W
Temperature Range100°C–450°C (212°F–842°F)
Kit ContentsAifen A902 station, C210 handle, C245 handle, 3 x C210 tips, 3 x C245 tips

Common Repair Uses

  • Board-level soldering, desoldering, and pad preparation across mobile and electronics repair.
  • Charging IC replacement
  • Charging port and connector re-soldering
  • Pad cleaning before reballing
  • Jumper wire repair on broken traces
  • Shield can removal and refitting
  • SMD component replacement
  • Ground-plane soldering with high thermal demand
  • General electronics and PC board repair

Compatible Devices

  • Universal — not device-specific. The station works on any PCB that suits its tip range, including smartphone, tablet, laptop, and PC boards.
  • Android smartphone logic boards
  • iPhone logic boards
  • Tablet motherboards
  • Laptop and PC motherboards
  • Charging port and FPC connector pads
  • SMD passive components and small ICs
  • BGA IC pads (cleaning and touch-up)
  • Shield cans and ground-plane areas

FAQ

What is the product name?
The product name is Aifen A902 Dual Soldering Station with 2 Handles and 6 Tips.
What is the brand of this product?
The brand of this product is Aifen.
What is the model of this product?
The model of this product is A902.
What is this product used for?
This product is used for board-level soldering, desoldering, and pad cleaning on mobile phone, tablet, and laptop PCBs.
Which devices are compatible with this product?
This product is universal and not device-specific. It works on any PCB that suits its C210 and C245 tip range.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which tip series fit the Aifen A902?
The Aifen A902 supports C115, C210, and C245 handles. The T245 handle also takes C470 heating elements.
Can I use both handles on the Aifen A902 at the same time?
Yes. The dual-station design runs both handles at the same time, and you switch either handle off independently.