Mijing HY-218 Multi-Functional Solder Paste
₨ 700
HY-218 Multifunctional Solder Paste
Mijing HY-218 solder paste gives your repair bench a no-clean tinning paste for oxidized pads, hard-to-tin metals and battery welding. It dips tin strongly, welds fast without a nickel transfer step, and leaves no residue, so you skip the cleaning round after every joint. The formula stays odorless and environmentally friendly, which suits a busy workshop where several technicians share one bench. Use it for oxidation point repair on boards, DIY welding jobs and battery soldering work. Mechanicpk supplies HY-218 to repair shops, service centers and technicians across Pakistan who want one dependable multi-purpose paste in their consumables drawer.
In stock
Mijing HY-218 Solder Paste for Oxidation and Battery Repair
Mijing HY-218 solder paste targets the jobs where plain flux and tin wire fail: oxidized points, metal surfaces that refuse tin, and battery welding. This multifunctional paste clings to the work area, wets the metal quickly and lets you tin a point in one pass. For a technician who already runs a hot air station and a soldering station, HY-218 covers the gap between a dedicated BGA solder paste and a basic liquid flux.
Key Technical Highlights
HY-218 dips tin strongly, so the solder flows onto the surface instead of beading off it. You do not need a nickel transfer step, which shortens every battery and tab welding job. The paste suits a range of metals that tin does not stain easily, a common obstacle on worn terminals and oxidized contacts. The formula leaves no residue, needs no cleaning and does not corrode the joint. The paste also stays odorless and environmentally friendly, so long bench sessions stay comfortable.
Repair Workflow Fit
Oxidation point repair is where HY-218 earns its place. When a board shows a hardware fault caused by a dull, oxidized pad, you apply a small amount of paste to the target area, heat it with your iron or hot air, and the pad tins cleanly. The same routine helps with a charging issue that traces back to a corroded contact, or a dead phone whose test points refuse solder. After tinning, you confirm the joint with a multimeter and inspect it under a microscope before closing the repair. Technicians who also run jumper lagana work on damaged tracks use the paste to prepare the pad before laying the wire.
Because the paste is no-clean, the board goes straight from soldering to testing. That saves a solvent wipe on every job and keeps your PCB holder free for the next unit.
Where HY-218 Sits Next to Other Consumables
HY-218 handles general tinning, DIY welding and battery soldering. For BGA reballing, pair your reballing kits with a dedicated tin paste and a stencil. For board cleaning after heavy rework, keep a separate flux remover on the bench. Think of HY-218 as the everyday problem-solver and the specialist consumables as your precision layer. Shops that scale from a single bench to a service center usually stock HY-218 in bulk alongside their soldering stations and hot air stations, because every technician reaches for it daily.
Why Technicians Choose This Paste
You choose HY-218 for speed and predictability. Strong tin uptake means fewer re-heats, and fewer re-heats mean less thermal stress on the board and nearby components. The no-residue finish gives you a clean joint to inspect, which matters when you check for cold joints or bridging under magnification. Mijing is a recognized name in mobile repair consumables, and HY-218 fits the same workshop routine as the rest of the range. If your daily jobs include oxidized contacts, battery tab welding or stubborn pads, HY-218 belongs within arm’s reach of your iron.
| Weight | 0.50 kg |
|---|
Key Features
- ✓High-activity multifunctional solder paste formula
- ✓Strong tin uptake on oxidized surfaces
- ✓No nickel transfer needed for fast welding
- ✓Suits metals that tin does not stain easily
- ✓No residue after soldering
- ✓No-clean and non-corrosive finish
- ✓Environmentally friendly and odorless
- ✓Suited to oxidation point repair, DIY welding and battery soldering
Specifications
| Brand | Mijing |
|---|---|
| Model | HY-218 |
| Category | Solder Flux & Paste |
Common Repair Uses
- ✓Oxidation point repair, battery soldering and general tinning in mobile and electronics repair
- ✓Oxidation point repair on motherboards
- ✓Battery welding and DIY battery soldering
- ✓Tinning pads before component placement
- ✓Tinning hard-to-tin metal surfaces
- ✓Preparing pads for jumper wire work
- ✓Repairing corroded contacts behind charging issues
- ✓Quick spot soldering where no cleaning is possible
- ✓General SMD and component rework
Compatible Devices
- ✓Universal — not device-specific; works on any board, contact or battery terminal that needs tinning
- ✓Mobile phone motherboards with oxidized pads
- ✓Oxidized test points and solder points on PCBs
- ✓Battery terminals and tabs for DIY battery welding
- ✓Metal surfaces that resist tin
- ✓Electronic component leads and pads
- ✓Worn or corroded charging-related contacts
- ✓Tracks and pads prepared for jumper wires
- ✓General electronic circuit boards in repair workflows
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Do I need to clean the board after using Mijing HY-218 solder paste?
Can HY-218 solder battery terminals without a nickel transfer step?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock



