Kailiwei Flywire UV 3S Nano Glue Green Oil 15g

₨ 1

Kailiwei UV 3S Flying Wire Green Oil

Kailiwei Flywire UV 3S is a 15g UV nano glue and flux-style green oil made for mobile mainboard repair. You use it to lock flying wires in place, insulate jumper joints, and cover damaged solder mask on the board. The 3S rapid-curing formula sets under a UV curing lamp, so you move from jumper lagana to the next step without waiting on slow-drying glue. Repair shops that handle charging issue, hardware fault, and dead phone boards use it as a standard consumable at the microscope bench. Mechanicpk stocks it for technicians who need a fast, dependable flying wire fixing oil.

Out of stock

13 People watching this product now!
Description

Kailiwei Flywire UV 3S for Flying Wire and Solder Mask Repair

Kailiwei Flywire UV 3S is a 15g UV nano glue and green oil that fixes flying wires and restores insulation on mobile phone mainboards. You apply a thin bead over a jumper wire, a repaired pad, or a lifted solder mask area. Then you cure it under a UV lamp. The “3S” in the product name points to its rapid-curing formula, which suits a repair workflow where every extra minute of waiting slows the next board.

How the 3S Rapid Cure Fits Your Bench

Slow-setting adhesives force you to hold a jumper wire still or leave a board untouched while the glue hardens. A UV-curing green oil removes that delay. The oil stays liquid until UV light hits it, so you position the wire exactly where you want it, check the placement under the microscope, and only then cure it. That control matters on dense boards where one stray wire can short a neighbouring pad.
Kailiwei sells this product as a special glue for flying wire work, and the green colour matches the solder mask on most phone boards, so repaired areas blend into the PCB. You need a UV curing lamp to set it. Keep the layer thin and even, because thick layers cure slower and leave soft spots underneath.

Flying Wire and Solder Mask Repair Workflow

Most technicians reach for this oil after the soldering is finished. You repair a broken trace, run a jumper from one pad to another, or reball and re-pad an IC area. Once the joint is clean and tested with a multimeter, you cover the exposed copper and wire path with the green oil and cure it. The cured layer locks the wire against the board, so vibration and handling no longer pull the jumper loose.
The same oil also patches solder mask that peeled during hot air rework. When you lift a shield or change an IC, the mask around the pads sometimes tears. A small dab of UV green oil seals the bare copper and keeps solder from bridging during the next pass. This workflow shows up constantly in charging issue, display problem, and dead after flash boards that need IC change karna followed by trace repair.
Always finish your soldering and flux cleaning before you apply the oil. Residue trapped under cured oil hides problems you will need to find later.

What to Pair With It on Your Repair Bench

This consumable works best as part of a complete PCB repair setup. A soldering station and hot air station handle the joint work, a microscope lets you place the wire and the oil precisely, and PCB holders keep the board steady while you cure. A multimeter confirms continuity before and after you seal the jumper, and a reballing kit covers the IC side of the same repair.
Mechanicpk carries these tool categories together, so you can build one order around the repair rather than buying piece by piece. If you run a high-volume shop, a 15g bottle gives you plenty of applications because each flying wire needs only a small amount of oil.
Store the bottle away from sunlight and strong lamps. UV-curing oil reacts to UV exposure, so a closed bottle in a drawer keeps the oil workable until you need it.

Additional information
Weight0.15 kg
Q & A
Please login to post questions

Key Features

  • 15g UV nano glue and green oil for mainboard repair
  • 3S rapid-curing formula
  • Made for flying wire fixing
  • Green colour blends with standard PCB solder mask
  • Stays liquid until UV light exposure, so you control placement
  • Insulates and protects repaired solder joints
  • Suits solder mask patch repairs after rework
  • Compact bottle for bench use

Specifications

BrandKailiwei
ModelFlywire UV 3S
CategoryUV Green Oil / Solder Mask Oil
CompatibilityUniversal for mobile phone mainboard repair (not device-specific)
TechnologyUV curing, 3S rapid cure
Weight15g

Common Repair Uses

  • Flying wire fixing and solder mask repair on mobile phone mainboards
  • Fixing flying wires and jumper wires to the board
  • Insulating repaired traces and jumper joints
  • Patching peeled or torn solder mask
  • Sealing bare copper after IC change
  • Protecting repaired pads after reballing
  • Securing wires on charging issue boards
  • Covering repaired areas on hardware fault boards
  • Locking jumper placement on dead phone boards

Compatible Devices

  • Universal — not device-specific; suited to mobile phone mainboards and similar PCBs
  • Android smartphone mainboards
  • iPhone logic boards
  • Multilayer mobile phone PCBs
  • BGA IC pad areas
  • SMD component pad areas
  • Charging port (tail plug) board area
  • FPC and flex connector pads
  • Jumper wire and flying wire points

FAQ

What is the product name?
The product name is Kailiwei Flywire UV 3S.
What is the brand of this product?
The brand of this product is Kailiwei.
What is the model of this product?
The model of this product is Flywire UV 3S.
What is this product used for?
This product is used for fixing flying wires and repairing solder mask on mobile phone mainboards.
Which devices are compatible with this product?
This product suits mobile phone mainboards and similar PCBs. It is universal and not device-specific.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Do I need a UV lamp to cure Kailiwei Flywire UV 3S?
Yes. This is a UV-curing oil, so it stays liquid until you expose it to UV light. Use a UV curing lamp to set it.
Can I use Kailiwei Flywire UV 3S to fix flying wires on a phone mainboard?
Yes. Kailiwei sells it as a special glue for flying wire work on mobile mainboards. It holds jumper wires in place and insulates the joint once cured.