KSLID S200 Motherboard Cleaning Sponge – 200 Pcs In Bottle
₨ 1
KSLID S200 Nano Cleaning Sponge
The KSLID S200 motherboard cleaning sponge removes soldering flux and residue from motherboards, chips, frames, and screens in one pass. Each bottle holds 200 high-density nanometer sponges that leave no flocculation and no residue behind. The manufacturer states they do not damage pads. You use them with a variety of cleaners, so they slot into the cleaning routine your repair bench already follows. Buy the S200 from Mechanicpk for your workshop or service center in Pakistan and keep clean boards moving from rework to testing.
Out of stock
Motherboard Cleaning Sponge Built for Flux and Residue Control
The KSLID S200 motherboard cleaning sponge gives your repair bench a purpose-built consumable for the last step of every board job: clearing flux and residue before you test. Each bottle holds 200 high-density nanometer sponges, so a busy workshop in Karachi, Lahore, or Islamabad keeps stock on hand without reordering every week. Mechanicpk supplies the S200 to technicians who treat cleaning as a measured part of the repair process. You use it on motherboards, chips, frames, and screens, and it targets soldering flux residue in particular.
How the High-Density Nanometer Structure Handles Residue
The S200 pairs a high-density nanometer build with strong adsorption, so the sponge lifts contamination in a single pass instead of smearing it across the board. The manufacturer lists no flocculation and no residue, which means you stop chasing loose fibres around SMD components after you finish wiping. The sponge does not drop material onto the surface, a real advantage when you work near fine-pitch pads and small passives. The manufacturer also states it causes no damage to pads, so you can clean freshly reworked areas with confidence. Because the sponge sheds nothing onto the surface, you wipe, turn it, and move to the next pad without stopping to pick debris off the board. That rhythm matters on a bench where every board waits for you. The sponge works with a variety of cleaners, which lets you keep the cleaning agent your bench already runs on.
Where the S200 Fits in Your Mobile Repair Workflow
Every IC change karna job leaves flux around the pads. You remove the chip with your hot air station or soldering station, clean the pads, place the new part, and flux spreads again. The S200 flux cleaning sponge clears that residue so you can inspect joints under your microscope before you close the board. After reballing, the same sponge cleans the area so your next continuity check with a multimeter reads a clean surface instead of burnt flux.
The sponge also earns its place on common hardware fault jobs. A charging issue board needs the area around the charging IC cleaned after you replace it. A display problem board needs the connector zone cleaned after you reflow it. A dead phone you revive through ISP work or an eMMC replacement needs its pads and surrounding board cleaned before you test it on your test box. Frames and screens collect adhesive dust and fingerprints during teardown, and the S200 handles those surfaces too, so one consumable covers your whole cleaning step. A clean board also makes it easier to read what your test box and multimeter show you.
Buying the S200 for a Workshop or Service Center
The S200 ships as a bottle of 200 sponges, which suits repair shops that clean boards daily and service centers that run several benches at once. A single bottle weighs 0.15 kg, so it stores easily next to your flux, solder, and PCB holders. You get a repeatable cleaning step for every technician on the floor, which keeps board finish consistent across jobs.
If you build out your cleaning and rework setup, pair the S200 with the tools that sit upstream in the same workflow. Soldering stations and hot air stations handle the rework itself. Reballing kits and PCB holders support BGA work and keep the board steady while you clean around it. Microscopes let you confirm the result before you power the board up. ISP pinout tools, eMMC programmers, and UFS adapters belong in the same dead-phone recovery chain, and the S200 keeps the boards clean as you move through each stage.
Choose the KSLID S200 from Mechanicpk when you want a high-density, no-residue motherboard cleaning sponge for flux cleaning in your Pakistani repair workshop.
| Weight | 0.10 kg |
|---|
Key Features
- ✓200 sponges per bottle for daily workshop use
- ✓High-density nanometer sponge structure
- ✓Strong adsorption cleans in one step
- ✓No flocculation and no residue
- ✓Does not drop or remain on the surface
- ✓No damage to pads
- ✓Works with a variety of cleaners
- ✓Cleans motherboards, chips, frames, and screens
Specifications
| Brand | KSLID |
|---|---|
| Model | S200 (200 pcs per bottle) |
| Category | Repair Accessories – PCB Cleaning Consumables |
| Compatibility | Universal, not device-specific |
| Supported Devices | Motherboards, chips, frames, and screens |
| Technology | High-density nanometer cleaning sponge |
| Weight | 0.15 kg |
Common Repair Uses
- ✓Flux and residue removal at the cleaning stage of board-level repair.
- ✓Clearing flux after IC change karna
- ✓Cleaning pads and surrounding area after reballing
- ✓Cleaning the charging IC area on a charging issue board
- ✓Cleaning the connector zone on a display problem board
- ✓Preparing a dead phone board before testing after ISP or eMMC work
- ✓Wiping the board before microscope inspection of solder joints
- ✓Cleaning phone frames after teardown
- ✓Cleaning screens during service
Compatible Devices
- ✓Universal cleaning consumable, not device-specific. The verified scope covers motherboards, chips, frames, and screens.
- ✓Mobile phone motherboards
- ✓PCB areas around soldered ICs
- ✓Chip surfaces
- ✓Pads after rework (no pad damage stated by the manufacturer)
- ✓Phone frames
- ✓Screens
- ✓Boards with soldering flux residue
- ✓Workshop boards from any brand (universal, not device-specific)
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does the KSLID S200 sponge leave fibres on the motherboard?
Which cleaners can I use with the KSLID S200 sponge?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



