YCS MY-CK01 Mr.Yang CPU Degumming Knife Set (10 Pcs)
₨ 800
YCS MY-CK01 Degumming Knife Set
The YCS MY-CK01 from the Mr.Yang range puts ten CPU degumming knives on your repair bench in one set. You use them to cut underfill glue around CPU and BGA chips, scrape old tin from pads, and pry ICs loose on mobile phone and tablet motherboards. Ten pieces mean you swap in a fresh blade when one wears down, so a glue-heavy board does not stall your queue. Pair the set with a hot air station and a microscope for controlled work on dead phone boards. Mechanicpk supplies the MY-CK01 to technicians, repair shops, and service centers across Pakistan.
In stock
CPU Degumming Knife Set for Mobile Repair: YCS MY-CK01 Overview
A CPU degumming knife set for mobile repair earns its place on the bench the moment a board arrives with black underfill glue around the processor. The YCS MY-CK01, sold under the Mr.Yang name, packs 10 degumming knives into one set, so you stop sharing a single worn blade across every job. Mechanicpk stocks it for Pakistani technicians who handle CPU, BGA, and IC work on mobile phone and tablet motherboards, from a quick chip lift to a full glue clean-up before reballing.
Where the MY-CK01 Fits in Your Rework Workflow
Underfill glue sits between the chip and the PCB, and you clear it before you lift a CPU or memory IC. The usual sequence runs in four moves. You warm the chip area with a hot air station, cut and scrape the edge glue with the knife, work the blade under the chip edge, and lift the IC once the solder softens. After the chip comes off, you scrape leftover glue and old tin from the pads so the board is ready for reballing or a replacement IC. The MY-CK01 covers the glue and tin stages of that sequence, which is where careless blade work can lift pads. Mount the board in a PCB holder and keep a microscope above it, so your hand stays steady and you see every pad you clean.
What the 10-Piece Set Gives Your Bench
Hardened epoxy wears an edge quickly, because you drag the blade across it again and again. A set of ten lets you rotate in a fresh knife instead of forcing a tired one, and you can dedicate separate pieces to glue cutting, tin scraping, and prying so one task never dulls the blade you need for the next. Workshops with several technicians can split the set across benches and keep every station supplied. Service centers that process boards daily can stock the pack as a consumable alongside flux, solder wick, and reballing kits.
Matching the Tool to the Repair
Most jobs that reach this knife start with a symptom: a dead phone, a hang on logo, a boot loop issue, or a charging issue that traces back to a board-level fault. When the diagnosis points to a CPU or a NAND chip, IC change karna begins with glue removal, and the quality of that step decides whether the pads survive. Hold the blade flat against the board, take light passes, and stop to check the pad surface under magnification instead of pushing through stubborn glue. After you clean the pads, test continuity with a multimeter before you place the new chip. If you replace an eMMC or UFS chip, you reprogram it with an eMMC programmer, an ISP pinout tool, or a UFS adapter, so a complete bench pairs the degumming knives with those tools plus a soldering station for the final reflow.
The MY-CK01 suits technicians who want a simple, replaceable-blade approach to glue work without buying a full hand-engraving kit. Start with this set for everyday CPU degumming. As your volume grows, add a stronger hot air station, a stereo microscope, and a dedicated reballing kit to handle the whole chip-off process in-house.
| Weight | 0.9 kg |
|---|
Key Features
- ✓10-piece set for continuous bench use
- ✓Designed for CPU degumming and glue removal
- ✓Handles tin scraping on motherboard pads
- ✓Supports IC removal and BGA chip prying
- ✓Suits mobile phone and tablet motherboard work
- ✓Sold under the Mr.Yang MY-CK01 model name
- ✓Replaceable pieces for rotating fresh edges
- ✓Fits workflows with hot air stations and microscopes
Specifications
| Brand | YCS (Mr.Yang) |
|---|---|
| Model | MY-CK01 |
| Category | CPU Degumming / Glue Removal Knives |
| Compatibility | Universal hand tool, not device-specific |
| Supported Devices | Mobile phone and tablet motherboards |
| Pack Quantity | 10 pieces per set |
Common Repair Uses
- ✓CPU and IC rework on mobile phone and tablet boards
- ✓CPU underfill glue removal
- ✓BGA chip prying and removal
- ✓IC disassembly
- ✓Tin and solder paste scraping from pads
- ✓Motherboard delamination
- ✓Pad cleaning before reballing or IC replacement
Compatible Devices
- ✓Universal CPU, BGA, and IC glue removal scope (not tied to a single phone brand or chipset)
- ✓Mobile phone motherboards
- ✓Tablet motherboards
- ✓CPU chips with underfill glue
- ✓BGA chips
- ✓IC chips and memory ICs
- ✓Solder pads after chip removal
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can the MY-CK01 pry a CPU chip, or does it only remove glue?
Should I heat the board before using a CPU degumming knife?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock



