2UUL SC18 Green Flux 50g Soldering Flux Paste
₨ 800
Green Flux Paste for Phone Boards
2UUL SC18 Green Flux 50g gives your bench a green soldering flux paste for mobile motherboard, PCB, BGA and SMD work. The pack holds 50g of flux (about 50ml), which covers daily IC replacement, pad dressing and reflow jobs without constant reordering. Distributor listings credit the paste with high activity, smooth solder flow and oxidation control on heated pads, and they describe it as smoke-free and non-conductive. Mechanicpk offers this 2UUL flux to technicians who want a paste-format consumable beside their hot air station and soldering station. Pick it up for dead phone and charging issue repairs that need clean wetting.
In stock
2UUL SC18 Green Flux for Mobile Repair: A Paste-Format Flux in a 50g Pack
The 2UUL SC18 green flux for mobile repair handles the flux step on nearly every board-level job. 2UUL SC18 Green Flux 50g arrives as a green paste with a 50g net weight and about 50ml net content. Supplier data places it on mobile motherboard, PCB, BGA and SMD soldering. Mechanicpk supplies it to buyers who already know how flux choice shapes joint quality and want one large container to portion from.
What the Paste Format Gives Your Bench
Paste stays where you put it. Thin liquid flux runs off a pad the moment you tilt the board in your PCB holder, while a paste holds its position on edges and around tight component clusters. You control how much flux reaches each pad.
Distributor descriptions credit SC18 with high activity and with reducing surface tension during soldering. Lower surface tension lets molten solder wet the pad and spread across the joint evenly. The same listings say the formula limits oxidation, so heated copper does not form a film that blocks that wetting. They also describe the paste as smoke-free and non-conductive, with easy application and minimal residue. Inspect every reworked area under your microscope anyway, and wipe leftover flux from fine-pitch pads when the board needs it.
Where SC18 Fits in a Repair Workflow
Flux sits between pad preparation and reflow. Take a dead phone with a hardware fault on the power section. You lift the failed IC with your hot air station, level the pads with your soldering station and wick, then spread a thin layer of SC18 before you place the replacement part. The paste keeps the pads wetted while the board heats, so the new IC settles onto clean, shiny solder.
Charging issue repairs follow the same pattern. You swap a charging IC or a damaged connector, flux the pads, solder, and check the rails with your multimeter once the joints cool. BGA-package work, such as eMMC reballing, uses the paste on stenciled pads from your reballing kits before the balls go on. A broken track also takes a jumper wire, and a dab of SC18 on the trace helps the jumper tin and bond cleanly.
Pack Details and What to Pair It With
The 50g pack suits shops where several technicians pull flux every day. Packaging measures 72 x 72 x 9 mm with a gross weight of 63g, so it stores easily in a bench drawer. A single technician gets months of use from one container, and a service center burns through it faster across multiple stations.
Build your consumables around the tools that surround the flux step. Your soldering stations and hot air stations set the heat, PCB holders lock the board, a microscope confirms every joint, and a multimeter verifies the circuit afterward. Add reballing kits and test boxes to the same order when you restock, and you cover prep, reflow and testing in one purchase. If you want the pack for hands-on IC-level work, 2UUL SC18 Green Flux 50g gives you volume, paste control and a formula aimed at mobile board soldering.
| Weight | 0.50 kg |
|---|
Key Features
- ✓Green soldering flux paste in a 50g pack with about 50ml net content
- ✓Aimed at mobile motherboard, PCB, BGA and SMD soldering
- ✓High-activity formula described by distributors for strong solder joints
- ✓Reduces surface tension so solder flows and spreads evenly
- ✓Limits oxidation on heated pads during rework
- ✓Described as smoke-free and non-conductive
- ✓Paste consistency stays in place on tilted boards and tight components
- ✓Easy application with minimal residue, per distributor listings
Specifications
| Brand | 2UUL |
|---|---|
| Model | SC18 |
| Category | Soldering Flux Paste |
| Compatibility | Mobile motherboard, PCB, BGA and SMD soldering |
| Supported Devices | Mobile phone, computer and electronic circuit boards |
| Weight | 50g net, 63g gross (net content about 50ml) |
| Dimensions | 72 x 72 x 9 mm (packaging) |
Common Repair Uses
- ✓Flux for the soldering and rework steps of board-level repair.
- ✓IC removal and replacement on dead phone boards
- ✓Charging IC and charging connector replacement for charging issue faults
- ✓SMD component replacement
- ✓BGA reflow and reballing preparation
- ✓Pad dressing and tinning after IC removal
- ✓Jumper wire soldering on broken tracks
- ✓Hardware fault repair on power section ICs
- ✓Rework with a hot air station on mobile motherboards
Compatible Devices
- ✓Universal flux, not device-specific. It supports soldering on any board you rework.
- ✓Mobile phone motherboards from any brand
- ✓Computer circuit boards
- ✓General electronic circuit boards
- ✓BGA packages
- ✓SMD components
- ✓PCB pads and solder joints
- ✓Boards reworked with a hot air station
- ✓Boards reworked with a soldering iron or soldering station
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is 2UUL SC18 suitable for BGA and SMD soldering on mobile boards?
How much flux does the 2UUL SC18 pack contain?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock



