2UUL DW16 Solder Vampire Desoldering Wick 2015 (10 Rolls)

₨ 2,500

2UUL DW16 Solder Vampire Wick

The 2UUL DW16 Solder Vampire 2015 is a 2.0 mm desoldering wick built for chip-level mobile repair. Each box holds ten individually wrapped rolls of roughly 1.5 m, so your bench keeps going through a full day of BGA clean-up. The Ultra Density oxygen-free copper braid pulls molten solder off CPU, NAND and eMMC pads and leaves a flat surface ready for reballing. You get consistent results on dead phone boards, charging port pads and stubborn solder bridges after every IC change. Pair it with your hot air station and soldering iron for a faster, cleaner rework cycle.

In stock

20 People watching this product now!
Description

Desoldering Wick for Mobile Repair Pakistan: 2UUL DW16 Solder Vampire 2015

The desoldering wick for mobile repair you pick decides how clean your pads look after every IC change karna job. The 2UUL DW16 Solder Vampire 2015 gives you a 2.0 mm wide braid of oxygen-free copper, woven with Ultra Density technology and packed as ten individually wrapped rolls of about 1.5 m each. You work it with a soldering iron or hot air station to lift leftover solder from BGA, CPU and NAND pads, and the braid front end holds its shape instead of scattering strands across the board.

How the Ultra Density Braid Pulls Solder Off the Pad

Ultra Density weaving packs the copper strands tighter than a loose braid, which raises capillary adhesion and heat transfer at the same time. You press the braid onto a molten joint with your iron tip, the heat runs along the copper, and the solder flows into the weave instead of sitting on the pad. The supplier describes fast tin absorption with no residue left behind, a result you notice most on a hardware fault board where one stray blob causes a short. Oxygen-free copper also resists oxidation, so a fresh roll from a sealed wrap conducts heat the way you expect.

Matching the 2.0 mm Width to Your Repair Bench

Choose a wick width equal to or slightly larger than the pad you clean. The 2015 size sits in the middle of the 2UUL Solder Vampire range, which also includes DW17 at 1.5 mm, DW18 at 2.5 mm and DW19 at 3.0 mm. At 2.0 mm, the DW16 covers the common pad fields you meet after lifting a CPU, NAND, eMMC or UFS chip on a mobile motherboard. Step down to DW17 when you clean tighter pad areas under a microscope, and step up to DW18 or DW19 for large ground areas.

Wick only removes exposed solder. Lift the chip first with a hot air station, then clean the leftover solder on the pads. The braid flexes enough to reach narrow spaces, so you protect nearby components and the board surface while you work.

Where the Wick Fits in a Chip-Level Workflow

Most technicians reach for wick at the same moment: right after IC removal and right before reballing. Hold your board in a PCB holder, remove the chip with hot air, drag the wick across the pads with a soldering station set to a sensible temperature, and check the result under a microscope. A quick multimeter check for shorts catches any bridge you missed, and then your reballing kit takes over. If the job is an eMMC or UFS repair, the same clean pads give your ISP pinout tool, eMMC programmer or UFS adapter a solid contact surface for reading, writing or a dead-after-flash recovery. Wick sits at the start of this chain, so a better pad here saves you a failed boot test at the end.

Buying Notes for Shops and Service Centers

Wick is a consumable. You cut off the used section after each pass and keep working with fresh braid, which burns through a roll faster than most shops expect. The 10-roll box gives a busy repair shop or a multi-technician service center a stock that lasts, and the individual wrapping keeps unopened rolls clean until you need them. The box weighs 96 g gross, so it ships and stores without fuss.

If you build a bench from the ground up, treat the DW16 as your daily-use width and add the matching soldering stations, hot air stations, microscopes and PCB holders from the same category as your volume grows. Mechanicpk stocks the full desoldering and rework range for technicians who want one dependable source for chip-level repair supplies across Pakistan.

Additional information
Weight0.96 kg
Q & A
Please login to post questions

Key Features

  • Ultra Density precision braiding for strong capillary adhesion
  • Fast heat conduction along the copper braid
  • Oxygen-free copper construction with oxidation resistance
  • 2.0 mm width suited to common BGA, CPU and NAND pad areas
  • Front end holds its shape without scattering strands
  • Flexible braid that fits narrow spaces on mobile boards
  • 10 individually wrapped rolls of approx. 1.5 m each
  • Sized within the 1.5 / 2.0 / 2.5 / 3.0 mm Solder Vampire range

Specifications

Brand2UUL
ModelDW16 Solder Vampire 2015
CategoryDesoldering Wick / Solder Wick
CompatibilityUniversal — works on any soldered PCB, not device-specific
TechnologyUltra Density braiding
MaterialOxygen-free copper braid
Width2.0 mm
Length per RollApprox. 1.5 m
Packaging10 rolls per box, individually wrapped
Dimensions46 x 46 x 12 mm (per roll)
Weight96 g (gross, per box)

Common Repair Uses

  • Removing leftover solder from pads during chip-level mobile and PCB repair
  • BGA pad cleaning after chip removal
  • CPU pad cleanup before reballing
  • NAND, eMMC and UFS pad preparation
  • Solder bridge removal on fine-pitch pads
  • Pad flattening after IC change karna
  • Charging port pad cleanup
  • Connector and test point cleanup
  • Board cleaning before ISP wire attachment

Compatible Devices

  • Universal — not device-specific; works on any soldered PCB or mobile motherboard
  • Android mobile phone motherboards
  • iPhone and other mobile logic boards
  • PCB motherboards
  • BGA pad fields
  • CPU pad areas
  • NAND and eMMC chip pads
  • Charging port and connector pads
  • Chip-level repair boards after IC removal

FAQ

What is the product name?
The product name is 2UUL DW16 Solder Vampire Desoldering Wick 2015.
What is the brand of this product?
The brand of this product is 2UUL.
What is the model of this product?
The model of this product is DW16 Solder Vampire 2015.
What is this product used for?
This product is used for removing leftover solder from PCB and mobile motherboard pads during chip-level repair and BGA rework.
Which devices are compatible with this product?
This product is universal and works on any soldered PCB, including mobile phone motherboards, BGA, CPU and NAND pads.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What width is the 2UUL DW16 desoldering wick and which pads does it suit?
The DW16 is 2.0 mm wide. Choose a wick width equal to or slightly larger than the pad you clean, and use the 1.5 mm DW17 for tighter areas or the 2.5 mm DW18 and 3.0 mm DW19 for larger areas.
Can desoldering wick remove solder balls under a BGA chip while the chip is still on the board?
No. Wick only removes exposed solder, so lift the chip with a hot air station first, then clean the remaining solder from the pads with the wick.