RF4 RF-ID01 Coil Tester – Type-C Inductor Fault Detector
₨ 1,000 Original price was: ₨ 1,000.₨ 650Current price is: ₨ 650.
RF4 RF-ID01 Coil Tester for Phone Board Inductor Checks
The RF4 RF-ID01 Coil Tester gives you a fast pass or fail check on motherboard inductors using electromagnetic induction. Power it through the USB-C interface, bring the 4 mm detection end to a coil, and read the light: on means normal, off means abnormal. The compact 78 mm body suits phone, tablet, and smart device boards, and it needs no software or setup. Use it on dead phone and charging issue jobs to find a faulty buck coil before you pick up the hot air station. Mechanicpk stocks it for technicians, repair shops, and service centers across Pakistan.
In stock
RF4 RF-ID01 Coil Tester: Light-On, Light-Off Inductor Diagnosis
The RF4 RF-ID01 Coil Tester is a pocket-size electromagnetic induction probe that checks motherboard inductors without multimeter leads, an LCR meter, or any software. When you power the RF4 RF-ID01 coil tester through its USB-C interface and bring it to a coil, the status light gives a direct verdict: light on means the inductor is normal, light off means it is abnormal. That single signal turns a dead phone or a charging issue into a short list of suspect coils, so you stop probing every buck coil by hand. Mechanicpk supplies it as a spec-defined diagnostic tool for technicians who already know what a coil failure looks like on the bench.
Technical Profile and Detection Principle
The RF-ID01 measures 78 mm in total length, 27 mm across the top, and 4 mm thick at the detection end. That slim tip fits between neighbouring components on a crowded board, so you can reach coils around the PMIC, the charging circuit, and the display power section. The tool works on electromagnetic induction, so it responds to the coil’s electromagnetic behaviour instead of reading a resistance across the pads. Plug-and-play operation removes drivers, apps, and setup time. Keep one limit in mind before you buy: the RF-ID01 returns a pass or fail indication, not a numeric inductance value. Use a multimeter or LCR meter when you need a measured figure, and use this tester when you need a fast verdict on whether a coil is alive. Thin dimensions matter on modern boards where coils sit close to shield cans and connectors, because a narrow probe cuts the risk of touching neighbouring parts.
Where the RF4 RF-ID01 Fits in Your Repair Workflow
Slot the RF-ID01 into the diagnostic stage, after visual inspection and before rework. Start under a microscope to spot burnt or cracked coils, check the rail with a multimeter, then run the coil tester across the buck coils on the shorted or dead section. An abnormal result gives you a precise target. You then clamp the board in a PCB holder, lift the coil with a hot air station or soldering station, fit a replacement, and test the new part before you close the phone. The same routine fits tablets and other smart electronic device boards, because the tool targets coil-type inductors rather than a specific brand or chipset. Technicians in Pakistani repair shops and service centers handle hardware fault jobs every day, including dead boards, charging issue cases, and phones that draw current but never start. A quick coil check rules out the inductor first. When the coil passes, you move on to ISP pinout tools, eMMC programmers, UFS adapters, or reballing kits. Record each result as you go: mark the abnormal coil on your job sheet, note which rail it feeds, and photograph the board before you desolder, so the customer sees the evidence behind the part replacement.
Why Workshops Stock an Inductor Tester for Mobile Repair
The RF-ID01 ships as a single induction tester, so you can equip every bench in a workshop instead of sharing one unit. Service centers use it for incoming board triage, repair shops use it during live jobs, and technical training institutes use it to show students how a buck coil fails and how to confirm it. Suppliers also position it for field maintenance, so you can carry it in a tool roll next to a multimeter and a test box. Because the verdict comes from a light, junior technicians interpret the result without learning meter ranges, and senior technicians keep their attention on the repair itself. Pair it with microscopes, multimeters, and hot air stations from Mechanicpk to build a complete board-level diagnostic bench around an inductor tester for mobile repair. The package contains one RF4 RF-ID01 induction tester, which keeps stocking and bench allocation simple for shop owners who order in quantity.
Key Features
- ✓Electromagnetic induction detection for motherboard inductors
- ✓Status light verdict: light on means normal, light off means abnormal
- ✓USB-C interface
- ✓Plug-and-play use with no software or drivers
- ✓4 mm slim detection end for tight board areas
- ✓Compact 78 mm body that fits a tool roll or bench drawer
- ✓Suits phone, tablet, and smart electronic device boards
- ✓Rapid fault point locking before rework
Specifications
| Brand | RF4 |
|---|---|
| Model | RF-ID01 |
| Category | Motherboard Coil (Inductor) Tester |
| Compatibility | Motherboards of mobile phones, tablets, and smart electronic devices |
| Technology | Electromagnetic induction |
| Dimensions | 78 mm total length × 27 mm top width × 4 mm detection-end thickness |
| Interface | USB-C |
Common Repair Uses
- ✓Inductor fault checking during board-level diagnostics on phones, tablets, and smart devices.
- ✓Locating a faulty inductor on a dead phone board
- ✓Checking buck coils after a rail short or power fault
- ✓Diagnosing charging issue jobs at the coil level
- ✓Screening suspect coils before choosing which part to replace
- ✓Verifying a replacement coil after soldering or hot air rework
- ✓Incoming board triage at service centers
- ✓Quick field and on-site coil checks
- ✓Demonstrating coil failure and testing in technical training labs
Compatible Devices
- ✓Universal, not device-specific. It tests coil-type inductors on phone, tablet, and smart device boards.
- ✓Smartphone motherboards with coil-type inductors
- ✓Tablet motherboards
- ✓Smart electronic device boards
- ✓Buck converter coils on power-management sections
- ✓Charging-circuit coils
- ✓Display and backlight power-section coils
- ✓Other power-rail coils on mobile boards
- ✓General electronic circuit boards with coil-type inductors
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
How do I read the RF4 RF-ID01 result on an inductor?
Does the RF-ID01 show the inductance value in µH?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock



