Mechanic Z10 (0.5mm) Solder Ball for BGA Reballing
₨ 1
0.5mm Solder Balls for BGA Reballing
Mechanic Z10 (0.5mm) Solder Ball 10000 Pieces gives your reballing bench a full bottle of leaded Sn63/Pb37 spheres. Use these 0.5mm solder balls for BGA reballing when you lift a CPU, eMMC, or power IC from a dead phone and need fresh contacts before you reflow the chip back onto the board. The plugged bottle keeps the balls under control while you sweep them across a stencil, and the 10000-piece count covers a long run of jobs. Repair shops in Pakistan can use this size for stencil-based reballing, board-level hardware fault work, and technician training benches.
Out of stock
0.5mm Solder Balls for BGA Reballing: Sn63/Pb37, 10000 Pieces per Bottle
Mechanic Z10 (0.5mm) Solder Ball 10000 Pieces packs 0.5mm solder balls for BGA reballing into one bottle built for a professional repair bench. Each ball uses a Sn63/Pb37 leaded alloy, the eutectic composition BGA technicians have relied on for decades. When a CPU, eMMC, or power IC lifts from a mobile board, the old balls collapse or tear away, and you need fresh spheres of a known diameter to rebuild every connection under the chip. This bottle supplies 10000 of them at 0.5mm, so you stop counting balls and focus on the rework.
Alloy and Ball Specification
Sn63/Pb37 melts and solidifies at a single temperature, around 183°C, instead of passing through a pasty range. That behaviour gives you a clean collapse during reflow and a predictable joint once the hot air stream moves away. Mechanic lists high purity and high sphericity for these spheres. Both matter because uneven balls leave uneven standoff height under the chip, and an uneven chip leaves open joints. The series also carries good thermal fatigue resistance and oxidation resistance, useful when a bottle sits on your bench for weeks between jobs. The 0.5mm diameter pairs with stencils cut for 0.5mm balls, so match stencil size to ball size before you start. Store this leaded alloy apart from your lead-free stock so the two never mix on one board.
Where It Fits in the Reballing Workflow
You reach for this bottle after the chip comes off. Lift the IC with your hot air station, clean the pads with a soldering station and desoldering wick, then apply flux and seat the chip in your PCB holder or reballing kit. Drop the matching stencil over the package, pour a small pile of balls, and sweep until every hole holds exactly one sphere. Tap off the excess, return it to the bottle, and reflow gently until the balls melt and settle onto the pads. Inspect the result under your microscope before you place the chip back on the board. The 10000-piece quantity suits repeated stencil work on CPU, eMMC, and PMIC packages without a refill mid-shift.
Repair Problems This Bottle Helps You Solve
Reballing earns its place when diagnosis points to broken BGA joints rather than software. A dead phone after a drop, a boot loop that returns after reflashing, a hang on logo, or a charging issue tied to a power IC often traces back to cracked balls under a chip. A network issue on a baseband package follows the same pattern. Once you confirm the fault with a multimeter and a power supply reading, fresh 0.5mm balls restore the physical contact the board lost. Service centers and training institutes also use a bottle like this for practice boards, since repeated reballing builds the hand control that clean stencil work demands. Pair it with flux, a matching stencil, and a steady heat profile for consistent results.
| Weight | 0.50 kg |
|---|
Key Features
- ✓10000 pieces of 0.5mm solder balls in one plugged bottle
- ✓Leaded Sn63/Pb37 eutectic alloy with a single melting point
- ✓High purity and high sphericity for even standoff height
- ✓Good thermal fatigue resistance for lasting BGA joints
- ✓Oxidation resistance for steady quality across long storage
- ✓Fits stencils cut for 0.5mm balls
- ✓Suits CPU, eMMC, and power IC reballing on mobile boards
- ✓Bulk quantity for busy repair shops and service centers
Specifications
| Brand Entity | Mechanic |
|---|---|
| Product Entity | Mechanic Z10 (0.5mm) Solder Ball 10000 Pieces |
| Technology Entity | BGA reballing, Sn63/Pb37 leaded solder alloy, stencil-based reball |
| Compatible Device Entities | BGA packages reballed with 0.5mm balls (mobile CPU, eMMC, PMIC) |
| Repair Process Entity | BGA IC reballing, board-level mobile repair |
| Industry Entity | Mobile phone repair industry, PCB rework |
Common Repair Uses
- ✓Real-world reballing and BGA rework scenarios.
- ✓Reballing a CPU lifted from a dead phone
- ✓Rebuilding eMMC contacts before reinstalling the chip
- ✓Reballing a power IC on a charging issue board
- ✓Fixing cracked joints behind a hang on logo fault
- ✓Restoring baseband IC contacts on a network issue board
- ✓Replacing lost balls after IC removal with hot air
- ✓Training new technicians on stencil reballing
- ✓Re-doing a failed reball on the same package
Compatible Devices
- ✓Universal consumable. Not tied to any phone model. It fits any BGA package you reball with a stencil sized for 0.5mm balls.
- ✓BGA ICs reballed with 0.5mm stencils
- ✓Mobile phone CPU packages on stencil-based reball jobs
- ✓eMMC chips that need new ball contacts
- ✓Power management ICs (PMIC) on mobile boards
- ✓Charging-related BGA ICs
- ✓Baseband and network BGA packages
- ✓Practice boards for technician training
- ✓Laptop and other PCB BGA chips sized for 0.5mm balls



