YCS-7050X HD Trinocular Microscope 7X-50X Zoom
₨ 50,500
Trinocular Microscope for Mobile Board Repair
The YCS-7050X HD Trinocular Microscope delivers continuous 7X to 50X synchronous zoom for micro-soldering, BGA inspection and board-level mobile repair. WF10X/23mm eyepieces sit on a 45-degree inclined head that swivels 360 degrees, and the trinocular port accepts a C-mount camera for screen output. A 144 LED light and a big aluminium alloy base keep the view bright and steady across long sessions. Mechanicpk supplies this trinocular microscope for mobile repair Pakistan technicians, repair shops and service centers that need dependable magnification for IC change, jumper work and PCB inspection.
Out of stock
YCS-7050X HD Trinocular Microscope: 7X-50X Optics for Micro-Soldering Benches
The YCS-7050X HD Trinocular Microscope gives your bench a continuous 7X to 50X synchronous zoom view of the board. It works as a dependable trinocular microscope for mobile repair Pakistan workshops that handle BGA, IC and connector jobs every day. The head tilts at 45 degrees and swivels 360 degrees, WF10X/23mm eyepieces carry the image to your eyes, and the third port takes a C-mount camera so the same view can go on a screen. A big aluminium alloy base keeps the head steady, and a 144 LED light lifts the detail on dark, crowded boards.
Optical Specification and Zoom Behaviour
The zoom range runs continuously from 7X to 50X, so you stop on the exact magnification a job needs instead of clicking between fixed steps. Start low to see the whole motherboard, then zoom in on one IC, one pad row or one cracked track without swapping objectives. The WF10X/23mm wide-field eyepieces give a comfortable field of view and adjust to your eyes, which matters when you spend hours on the bench. The 45-degree inclined head rotates through 360 degrees, so you can turn the eyepieces to the side to share the view with a colleague or to fit a cramped bench layout.
A 7X to 50X range suits mobile board work because most jobs fall in the middle of it. Low magnification covers general inspection, flux cleaning and component placement. Mid-range magnification covers connector pins, small passives and the edges of a BGA package. The upper end helps with hairline track damage and tiny pads under a camera or battery connector. If you need more than 50X for a specific task, the manufacturer lists an objective lens as an optional accessory. Depth of field narrows as you zoom in, so you will switch between magnifications during one repair. Zoom out to position the tip, zoom in to confirm the joint, and zoom out again to check the surrounding components for heat damage. That habit keeps your hands safe from guesswork and keeps the neighbouring parts safe from your iron. New technicians pick up the rhythm within a few boards, and experienced ones rarely leave the zoom knob alone.
Trinocular Port and Camera Setup
The third viewing port is what separates this microscope from a binocular stereo unit. A C-mount CTV adapter lens connects a camera to that port, and the manufacturer lists an HDMI 4K camera as an optional accessory. Order the camera with the microscope if you want screen output from day one. With a camera attached, you can watch a reballing job on a monitor, show a customer the burnt IC on a dead phone, record before and after results for your own reference, and train junior technicians on the same live image you see. Eyepiece viewing and camera output run together, so you never give up one to use the other.
Trinocular Microscope for Mobile Repair Pakistan Buyers: Bench Workflow Fit
Most boards that reach a repair shop need magnification before a single wire gets soldered. A charging issue, a display problem or a hardware fault usually ends at a damaged connector, a lifted pad or a burnt power IC, and you need clear sight of all three. The YCS-7050X sits at the start and the end of that workflow. You inspect the fault under it, then check the finished joint under it after the work. It supports IC change karna on boards that need a hot air station, jumper lagana on broken tracks, and fine wire soldering on ISP pinout points when you work on an eMMC or a UFS fault. Pair it with a soldering station and a PCB holder, and your hands stay free for the actual rework.
A microscope touches every stage of board-level work, so it earns its bench space. During diagnostics, you scan the board for corrosion, burnt components, cracked solder joints and bent pins before you touch a multimeter probe. During rework, you watch the solder melt and the IC settle while the hot air station runs, which tells you when to stop heating. During flashing and programming jobs on a dead after flash phone, you use it to place fine ISP wires on the right test points and confirm no neighbouring pad shares the solder. During final testing, you recheck the joints before you close the phone and hand it back. Each step shortens when you see the fault clearly, and each repeat visit you avoid saves your shop time and parts.
Build, Base and Long-Session Use
The big aluminium alloy base gives the head a solid footing, so the image stays still when you move tweezers or lean on the bench. The 144 LED light sits around the lens and lights the board evenly, which cuts shadows from tall components such as connectors and shields. That even light also helps when you look for solder bridges and flux residue after reballing. A stereo view gives you real depth perception, so you judge how far a tip sits above a pad. That depth cue is the reason technicians choose a stereo microscope over a flat digital screen for fine soldering. The manufacturer also lists the same optics for biological work and precision instrument inspection, so the unit stays useful outside phone repair.
Choosing the Right Set for Your Shop
Check which set you order. The microscope ships in a standard configuration with the head, eyepieces, base, light and a CTV adapter lens, and distributors list the 4K camera and swing arm brackets as separate options. If your shop does dead phone recovery and board-level work all day, the camera set pays back through faster training and clearer customer proof. If you only need inspection and soldering magnification, the standard set covers that. Shops that grow into reballing and BGA work can build a full bench around it with a hot air station, a reballing kit, a multimeter and a test box, so one microscope anchors the whole setup. Mechanicpk stocks the matching bench tools, so you can buy the full workflow from one place. Compare the set contents line by line before you pay, because two listings with the same model name can differ in lens, light and camera. Ask your supplier to confirm the exact adapter lens and light in the box so you know your bench will run the day it arrives.
| Weight | 6.0 kg |
|---|
Key Features
- ✓Continuous 7X to 50X synchronous zoom
- ✓45-degree inclined trinocular head with 360-degree swivel
- ✓WF10X/23mm adjustable wide-field eyepieces
- ✓Trinocular port with C-mount CTV adapter lens for camera output
- ✓Optional HDMI 4K camera and objective lens accessories
- ✓144 LED light for even board illumination
- ✓Big aluminium alloy base for a steady image
- ✓Suited to mobile phone repair, PCB and BGA work, motherboard soldering and precision inspection
Specifications
| Brand Entity | YCS |
|---|---|
| Product Entity | YCS-7050X HD Trinocular Microscope |
| Technology Entity | Trinocular stereo microscope with 7X-50X continuous synchronous zoom and C-mount camera port |
| Compatible Device Entities | Mobile phone motherboards, PCBs, BGA ICs, eMMC and UFS ISP pinout points |
| Repair Process Entity | Micro-soldering, BGA reballing inspection, IC rework, PCB inspection |
| Industry Entity | Mobile phone repair, GSM repair workshops, electronics rework |
Common Repair Uses
- ✓Board inspection and fine soldering across the mobile repair workflow.
- ✓BGA IC inspection before and after reballing
- ✓IC removal and replacement (IC change karna)
- ✓Charging port and connector soldering
- ✓Jumper wire placement on broken tracks (jumper lagana)
- ✓ISP pinout wire soldering on eMMC and UFS test points
- ✓Corrosion and burnt component inspection on dead phones
- ✓Solder bridge and flux residue checks
- ✓Recording repair work through a C-mount camera for training and customer proof
Compatible Devices
- ✓Universal, not device-specific. It inspects any board that fits under the lens.
- ✓Samsung motherboards
- ✓iPhone motherboards
- ✓Oppo and Vivo motherboards
- ✓Infinix and Tecno motherboards
- ✓Xiaomi and Realme motherboards
- ✓BGA IC packages (eMMC, UFS, CPU, PMIC)
- ✓Laptop and tablet PCBs
- ✓C-mount cameras (through the CTV adapter lens)
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What magnification range does the YCS-7050X cover?
Can I connect a camera to the YCS-7050X for HDMI output?
Related products
SUNSHINE LS3 Plus LCD Screen Separator
In stock
YCS-6575X Ultra HD Trinocular Microscope 6.5X-75X
In stock



