Relife RL-044 XM12 Stencil – SM8250 BGA Reballing Template
₨ 599
SM8250 Reballing Stencil for Xiaomi 10 Boards
The Relife RL-044 XM12 Stencil is a 0.12 mm steel BGA reballing plate built for the Qualcomm Snapdragon 865 SM8250 CPU footprint. It covers the CPU position on Xiaomi 10, Xiaomi 10 Pro and Redmi K30 Pro motherboards, so you place solder balls on the exact pad layout instead of guessing with a universal plate. Round and square hole positions shape clean, even balls, and the steel body stays flat under hot air. Pair it with a hot air station, a PCB holder and a microscope for a controlled CPU reball on flagship Xiaomi boards.
In stock
SM8250 BGA Reballing Stencil Matched to the Xiaomi 10 Series CPU
The Relife RL-044 XM12 Stencil is an SM8250 BGA reballing stencil that matches the Qualcomm Snapdragon 865 CPU footprint. You use it on Xiaomi 10, Xiaomi 10 Pro and Redmi K30 Pro boards when a CPU needs fresh solder balls after removal or replacement. The XM12 plate belongs to the Relife RL-044 Xiaomi series, where each numbered plate maps to one chipset footprint instead of covering several packages. That one-to-one mapping keeps ball position and pad pattern exact, which matters on a flagship-class BGA package where a few misplaced balls turn a clean rework into a dead phone.
Technical Highlights of the XM12 Plate
The XM12 plate measures 0.12 mm thick and uses steel construction. The RL-044 series uses round and square hole positions to form rounded solder balls across the pad array. Steel resists warping under heat, so the plate keeps its shape when you work with a hot air station. The thin profile sits tight against the chip surface, which helps paste or ball transfer into every aperture. This plate targets Snapdragon 865 SM8250 only. The neighbouring XM10, XM14 and XM15 plates cover other Snapdragon platforms, so always match the plate number to the CPU marking on your board before you start.
Where It Fits in the CPU Reballing Workflow
A CPU reball starts at the hot air station: you lift the chip, clean the pads with flux and desoldering wick, and inspect every pad under a microscope. Clamp the board in a PCB holder, align the XM12 plate over the pads, and fill the apertures with solder paste or place balls through them. Then reflow the chip carefully and check the result before you refit the shield. This stencil handles the ball placement step, and it works best alongside a good soldering station, a reballing kit with quality solder balls and a multimeter for continuity checks after reassembly. If your bench also runs ISP pinout tools, eMMC programmers or test boxes, the stencil covers the hardware side while those tools cover the software side of the same job.
Why Technicians Pick a Dedicated SM8250 Plate
Universal plates force you to compromise on pad alignment. A dedicated XM12 plate removes that compromise, which saves rework on boards that already carry a high repair value. When a Xiaomi 10 series phone comes in as a dead phone after a drop, or hangs on logo because of a suspected CPU joint fault, a reball is one of the repair paths you test after you confirm the fault with a multimeter and board-level checks. Repair shops and service centres in Pakistan that handle Xiaomi and Redmi flagship boards keep a plate like this on the bench so a CPU reball does not wait on a supplier. Training institutes also use single-footprint plates to teach clean alignment and ball formation on a real Snapdragon package.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Matches the Qualcomm Snapdragon 865 SM8250 CPU footprint
- ✓Covers Xiaomi 10, Xiaomi 10 Pro and Redmi K30 Pro CPU positions
- ✓0.12 mm thickness for close contact with the chip surface
- ✓Steel construction that resists warping under heat
- ✓Round and square hole positions for rounded, even solder balls
- ✓Part of the Relife RL-044 Xiaomi series with one plate per chipset footprint
- ✓Single-footprint plate that avoids universal-stencil alignment compromises
- ✓Works with hot air stations, PCB holders, microscopes and reballing kits
Specifications
| Brand | Relife |
|---|---|
| Model | RL-044 XM12 |
| Category | BGA Reballing Stencil |
| Compatibility | Qualcomm Snapdragon 865 SM8250 CPU footprint |
| Supported Devices | Xiaomi 10, Xiaomi 10 Pro, Redmi K30 Pro |
| Technology | Round and square hole steel stencil, 0.12 mm thickness |
| Material | Steel |
Common Repair Uses
- ✓CPU-level reballing on Snapdragon 865 SM8250 boards
- ✓Reballing an SM8250 CPU after hot air removal
- ✓Replacing solder balls on a CPU you plan to refit to the same board
- ✓Re-balling a replacement CPU before installation
- ✓Restoring even ball height and pitch after pad cleaning
- ✓Board-level rework on Xiaomi 10 and Xiaomi 10 Pro motherboards
- ✓Board-level rework on Redmi K30 Pro motherboards
Compatible Devices
- ✓Snapdragon 865 SM8250 CPU footprint on the Xiaomi and Redmi models below
- ✓Xiaomi 10
- ✓Xiaomi 10 Pro
- ✓Redmi K30 Pro
- ✓Any board carrying the Qualcomm Snapdragon 865 SM8250 CPU in the same footprint
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which chipset does the Relife RL-044 XM12 stencil fit?
Can I use the XM12 stencil on a Snapdragon 888 or Snapdragon 8 Gen 1 board?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock



