Amaoe QU8 Stencil – 0.12mm Qualcomm BGA Reballing

₨ 1

Qualcomm BGA Reballing Stencil, 0.12mm

Amaoe QU8 Stencil is a 0.12mm BGA reballing stencil with square holes for Qualcomm CPU and RAM rework. It covers SM8250-102 CPU, SM8250-102 RAM, SM8250-002 CPU, SM8350 RAM, SM8250-002 RAM, SDM439, SM8350 and Snapdragon 888 series chips. A heat hole anti-bulge design keeps the sheet flat during reflow, and the reusable net handles repeated tin planting jobs on your repair bench. Technicians use it after hot air removal to restore solder balls on a lifted CPU or RAM chip from a dead phone or hardware fault board. Match your chip marking against the supported list before you start reballing.

Out of stock

18 People watching this product now!
Description

Amaoe QU8 BGA Reballing Stencil for Qualcomm CPU Rework

The Amaoe QU8 Stencil is a 0.12mm BGA reballing stencil built for a defined set of Qualcomm packages: SM8250-102 CPU, SM8250-102 RAM, SM8250-002 CPU, SM8350 RAM, SM8250-002 RAM, SDM439, SM8350 and Snapdragon 888 series chips. If your bench handles these boards, the Amaoe QU8 BGA reballing stencil gives you one square-hole tin planting net that matches those pad layouts. You reball a lifted CPU or RAM chip without improvising a pattern. Mechanicpk lists it for Pakistani repair shops and service centers that treat reballing as routine board-level work.

Stencil Build and Tin Planting Behavior

The stencil uses 0.12mm sheet thickness with square holes, and you can reuse it across jobs. A heat hole anti-bulge layout sits in the sheet to resist warping when the net meets reflow temperatures. That matters because a bowed stencil lets balls drift off their pads and leaves you with bridged or missing joints. You get a flat template that sits tight against the chip surface, so each pad receives its own ball. Wash the plate with flux remover after every job and it stays ready for the next chip, which keeps your cost per reball low across a busy week.

Snapdragon 888 Reballing Stencil Coverage and Chip Matching

Coverage centers on Qualcomm silicon. The CPU and RAM entries for SM8250-102 and SM8250-002 share this plate with SM8350 RAM, SM8350, SDM439 and Snapdragon 888 series parts, which makes it a practical SM8250 BGA stencil for technicians who see these chips often. Pad layout follows the chip package, not the phone name, so Mechanicpk does not tie this stencil to individual handset models. Read the marking on your chip, compare it with the list above, and confirm the match before you apply flux. A wrong plate on a good CPU costs you the chip, so a few seconds of checking saves the whole board.

Where the QU8 Fits in Your Reballing Workflow

Most jobs start with a dead phone or a hardware fault that traces back to a CPU or RAM joint: a boot loop issue, a hang on logo, or no power after a drop. You lift the chip with a hot air station or rework station, then clean the board pads with a soldering station and desoldering wick. Clean the chip itself next, and seat it on a reballing platform. Align the QU8 stencil over the pads and press it flat against the chip. Apply paste or drop balls, then reflow with controlled heat until the balls form. Let the chip cool before you lift the stencil.

Inspect the result under a microscope for missing or merged balls. Then place the chip back on the board in a PCB holder and reflow it. Use a multimeter to check continuity once the board cools. Mechanicpk carries Reballing Kits, Hot Air Stations, Soldering Stations, Microscopes, Multimeters and PCB Holders that complete this bench, plus ISP Pinout Tools, eMMC Programmers and Test Boxes for the software side of the same repair.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • 0.12mm stencil thickness
  • Square hole design for solder ball planting
  • Heat hole anti-bulge design to resist warping at reflow temperature
  • Reusable stencil for repeated reballing jobs
  • Covers SM8250-102 and SM8250-002 CPU and RAM
  • Covers SM8350, SM8350 RAM and SDM439
  • Covers Snapdragon 888 series chips
  • Compact, light plate that stores easily with other reballing stencils

Specifications

BrandAmaoe
ModelQU8
CategoryBGA Reballing Stencil
CompatibilityQualcomm CPU and RAM packages
Supported DevicesSM8250-102 CPU, SM8250-102 RAM, SM8250-002 CPU, SM8350 RAM, SM8250-002 RAM, SDM439, SM8350, Snapdragon 888 series
Technology0.12mm BGA reballing stencil, square holes, heat hole anti-bulge design

Common Repair Uses

  • Reballing a Qualcomm CPU after hot air removal
  • Reballing SM8250 and SM8350 RAM chips
  • Restoring balls on a CPU lifted from a dead phone
  • Tin planting after a chip reflow repair on a hardware fault board
  • Reballing SDM439 CPUs during board-level repair
  • Reusing a good chip after cleaning old solder from the pads
  • Rebuilding balls on a CPU after a boot loop issue traces to a weak joint
  • Preparing a chip for reattachment under a microscope

Compatible Devices

  • Qualcomm chipset families only. Device-level phone models are not verified, so the scope is chip-based.
  • SM8250-102 CPU
  • SM8250-102 RAM
  • SM8250-002 CPU
  • SM8350 RAM
  • SM8250-002 RAM
  • SDM439
  • SM8350
  • Snapdragon 888 series chips

FAQ

What is the product name?
The product name is Amaoe QU8 Stencil.
What is the brand of this product?
The brand of this product is Amaoe.
What is the model of this product?
The model of this product is QU8.
What is this product used for?
This product is used for BGA reballing of supported Qualcomm CPU and RAM chips.
Which devices are compatible with this product?
This product is compatible with Qualcomm SM8250-102 CPU and RAM, SM8250-002 CPU and RAM, SM8350 and SM8350 RAM, SDM439, and Snapdragon 888 series chips.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which Qualcomm chips does the Amaoe QU8 stencil support?
The Amaoe QU8 stencil supports SM8250-102 CPU, SM8250-102 RAM, SM8250-002 CPU, SM8350 RAM, SM8250-002 RAM, SDM439, SM8350 and Snapdragon 888 series chips.
What is the thickness of the Amaoe QU8 stencil and can you reuse it?
The Amaoe QU8 stencil is 0.12mm thick with square holes and a heat hole anti-bulge design, and you can reuse it for repeated reballing jobs.