Amaoe Stencil RF1 BGA – PA IC Reballing Steel Mesh
₨ 1
Amaoe RF1 BGA Stencil for RF Power Amplifier ICs
The Amaoe Stencil RF1 BGA is a steel mesh reballing stencil for RF power amplifier ICs. Amaoe lists its RF1/RF2 series for four part numbers: 77031, QPM5677, 53735 and 78191-11. The apertures fix each ball position, so you plant tin evenly across the PA package and reflow it with your hot air station. Amaoe describes the material as deformation resistant, so the plate holds its shape through repeated heat cycles. If network issue and hardware fault repairs fill your bench, this Amaoe RF1 BGA stencil gives you a repeatable reball for power amplifier chips.
Out of stock
Amaoe RF1 BGA Stencil: Reballing Precision for RF Power Amplifier ICs
The Amaoe Stencil RF1 BGA handles one specific job: reballing RF power amplifier ICs after you lift them from the board. Amaoe lists its RF1/RF2 series for four part numbers, 77031, QPM5677, 53735 and 78191-11, and builds the stencil from steel mesh with apertures that fix every ball position. A generic universal template rarely matches a PA package pad for pad, so a part-number-specific Amaoe RF1 BGA stencil earns its place on any bench that reworks network modules. You pair it with solder paste or balls, flux and a hot air station, and you get a chip that seats back onto the PCB with a clean ball array. The stencil suits technicians who reball PA ICs on a regular basis, not only on the occasional repair.
Key Technical Highlights
Steel mesh gives this stencil the rigidity that thin plastic or paper templates lack. Amaoe describes the material as deformation resistant, which matters when you heat the plate directly with hot air and a weaker sheet would warp and shift off the pads. The apertures sit at fixed positions, so each ball or tin deposit lands where the pad sits instead of drifting during reflow. Amaoe describes the aperture shape as square round holes. You do not measure ball pitch yourself. You match the stencil to the chip part number, and the aperture layout does the alignment work. Uniform deposits across the array also cut the risk of bridging between neighbouring pads when you reflow. Handle the plate by its edges, clean flux residue off it with isopropyl alcohol after each use, and store it flat so the apertures keep their shape.
Where It Fits in Your Repair Workflow
RF power amplifier work usually starts with a network issue on a handset: weak or missing signal, or a hardware fault you trace to the transmit chain. You confirm the fault with a multimeter and a microscope, then lift the suspect PA IC with a hot air station while a PCB holder keeps the board steady. A soldering station and desoldering wick clear old solder from the pads on both the board and the chip. Reballing comes next. You lay the Amaoe stencil over the cleaned PA IC, press tin or balls through the apertures, and reflow with controlled heat until the deposits form uniform balls. Work under the microscope while you press the tin through, because a single missed aperture leaves a gap you only find after reflow. You then refit the chip and test the board. Keep the stencil flat against the chip while you work, and let the board cool before you lift the plate so the new balls stay seated.
If you stock a full reballing bench, this stencil sits alongside the reballing kits, hot air stations, soldering stations and microscopes your technicians already use. It covers the RF stage, while CPU and memory work calls for different stencils. Shops that also handle dead phone and boot loop cases will pair it with eMMC programmers, UFS adapters and ISP pinout tools, then use a test box for final checks.
Why Technicians Buy the Amaoe RF1 Stencil
Replacing a whole board for a faulty PA IC costs far more than a stencil and a reball. Repair shops and service centers buy the stencil because it turns a one-off IC change into a repeatable bench procedure for every handset that uses these four part numbers. A reball also saves a chip you can still reuse, which keeps the customer’s repair bill down on handsets where a donor board costs more. Amaoe supplies it new, so you start with an unused plate. Check the part number printed on your chip against 77031, QPM5677, 53735 or 78191-11 before you order, since Amaoe’s listing covers the RF1/RF2 series without splitting the numbers between the two. Mechanicpk supplies the Amaoe Stencil RF1 BGA to workshops across Pakistan.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Steel mesh stencil body
- ✓Deformation-resistant material for repeated heating
- ✓Precise pin location across the aperture pattern
- ✓Square round hole apertures
- ✓Covers the 77031 power amplifier IC
- ✓Covers the QPM5677 power amplifier IC
- ✓Covers the 53735 and 78191-11 power amplifier ICs
- ✓Brand-new Amaoe stencil built for RF power amplifier IC reballing
Specifications
| Brand | Amaoe |
|---|---|
| Model | RF1 (listed by Amaoe as the RF1/RF2 series) |
| Category | BGA Reballing Stencil |
| Compatibility | RF power amplifier ICs 77031, QPM5677, 53735, 78191-11 |
| Technology | BGA reballing (tin planting) stencil |
| Material | Steel mesh |
Common Repair Uses
- ✓Board-level reballing of RF power amplifier ICs.
- ✓Reballing a PA IC after you lift it from the board
- ✓Board-level repair of a network issue traced to the power amplifier stage
- ✓Re-tinning a salvaged PA IC before you refit it
- ✓Refitting a PA IC after you clean old solder from its pads
Compatible Devices
- ✓Universal, not device-specific. Compatibility follows the RF power amplifier IC part number, not the phone model.
- ✓RF power amplifier IC 77031
- ✓RF power amplifier IC QPM5677
- ✓RF power amplifier IC 53735
- ✓RF power amplifier IC 78191-11
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which RF power amplifier ICs does the Amaoe RF1 BGA stencil cover?
Does the Amaoe RF1 stencil need a hot air station to reball a PA IC?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



