2UUL SC55 UV Curable Solder Mask 10cc

₨ 499

UV Curable Solder Mask for PCB Repair

The 2UUL SC55 UV curable solder mask restores the insulating layer on a mobile phone motherboard after trace repair, jumper work, or IC rework. The 10cc syringe delivers the resin through a fine tip, so you place it exactly where the board needs cover. The mask stays liquid until UV light hits it, which gives you unlimited working time to position and inspect. It hardens in about 30 seconds under a UV lamp, and a 3-minute cure sets it firm. The cured coat is non-conductive and shields repaired copper from shorts and moisture. Mechanicpk supplies the SC55 to technicians and repair shops across Pakistan.

Out of stock

11 People watching this product now!
Description

2UUL SC55 UV Curable Solder Mask for Motherboard Repair

The 2UUL SC55 UV curable solder mask rebuilds the protective layer on a phone motherboard once your repair is finished. The 10cc syringe holds a UV-reactive resin that stays liquid on the board until ultraviolet light reaches it. You place the coat precisely, check the edges under magnification, and cure it on your own timing. Mechanicpk stocks the SC55 for technicians in Pakistan who need a dependable mask coat after trace rebuilds, jumper wire jobs, and BGA rework.

Technical Highlights of the SC55 Formula

SC55 cures only when UV light reaches it, so the resin gives you unlimited working time after you apply it. You can clean up the edges and confirm coverage before you commit to the cure. Supplier data lists a hardening time of roughly 30 seconds under a UV lamp, with about 3 minutes recommended for a firm, fully set coat. Sunlight also cures the resin, which helps when your lamp is busy on another board. The cured layer is non-conductive, so it insulates exposed copper and repaired tracks against shorts. The resin does not dry out inside the syringe, so one 10cc tube covers many jobs across your bench instead of going to waste half-used.

Where It Fits in Your Repair Workflow

Solder mask work closes a repair rather than opening it. After an IC change karna job, a trace rebuild, or a jumper lagana fix on a dead phone, the board often shows bare copper or a scraped mask layer. You clean the area with flux remover, place the SC55 over the exposed pad or wire run, and cure it. The coat covers gaps in the laminate, locks jumper wires in position, and keeps the repaired section away from moisture and stray solder. Technicians reach for it on charging issue repairs, hardware fault tracing, and board restoration after liquid damage cleaning. Pair it with a microscope for precise placement, a soldering station or hot air station for the rework itself, a reballing kit for BGA jobs, and a PCB holder that keeps the board steady while the mask sets.

Application and Curing Notes for Your Bench

Apply a thin, even layer through the fine syringe tip and keep the mask on the intended area only. Keep it off connector contacts, test points you still need, and any pad you plan to solder again. Cure under your UV lamp until the surface turns hard. Give it the full 3 minutes when the repair carries stress, such as a jumper wire route near a board edge that flexes. Cap the syringe after each job and store it away from direct sunlight, because UV exposure starts the cure inside the tip. Buy a lamp that matches your bench routine, since the SC55 needs UV light to harden and nothing else in your kit replaces that step. Technicians who run high repair volume in Pakistan usually keep a spare syringe on the bench so a cured tip never stalls a job.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • 10cc syringe with fine tip for precise placement
  • Hardens in about 30 seconds under UV light
  • 3-minute cure recommended for a firm, fully set coat
  • Cures under sunlight when no UV lamp is free
  • Stays liquid until UV exposure, so working time has no limit
  • Non-conductive after curing for reliable insulation
  • Resin does not dry out in the syringe
  • Suits mobile phone PCB, BGA, PGA, and SMD rework

Specifications

Brand2UUL
ModelSC55
CategoryUV Curable Solder Mask / PCB Repair Consumable
CompatibilityUniversal, not device-specific
TechnologyUV light curing (about 30 seconds to harden, 3 minutes recommended for a firm set)
Capacity10cc syringe

Common Repair Uses

  • Covering exposed copper traces
  • Securing jumper wires after jumper lagana
  • Closing gaps in the laminate after track repair
  • Protecting the area after IC change karna
  • Reinforcing weak solder joints
  • Restoring mask layers scraped during rework
  • Sealing board areas after BGA and SMD rework

Compatible Devices

  • Universal PCB repair consumable, not locked to specific phone models
  • Android smartphone motherboards
  • iPhone logic boards
  • Mobile phone BGA IC areas after rework
  • PGA and SMD component areas
  • Jumper wire routes on repaired boards
  • Rebuilt PCB tracks and lugs
  • Exposed copper on scraped solder mask layers
  • General electronics PCBs

FAQ

What is the product name?
The product name is 2UUL SC55 UV Curable Solder Mask 10cc.
What is the brand of this product?
The brand of this product is 2UUL.
What is the model of this product?
The model of this product is SC55.
What is this product used for?
This product insulates and protects repaired PCB areas, covers exposed copper, and secures jumper wires on mobile phone motherboards.
Which devices are compatible with this product?
This product is a universal PCB repair consumable. It works on mobile phone motherboards and other circuit boards and is not limited to specific models.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Does the 2UUL SC55 solder mask harden without a UV lamp?
The mask needs UV light to harden. A UV lamp cures it in about 30 seconds, and sunlight also cures it. Without UV exposure, the mask stays liquid.
How long should I cure SC55 on a repaired board?
The mask hardens in about 30 seconds under UV light. A cure time of about 3 minutes is recommended for a firm, fully set coat.