Amaoe WC1 Reballing Stencil for Qualcomm WCN/WCD ICs

₨ 599

Amaoe WC1 Stencil for Qualcomm WCN/WCD

The Amaoe WC1 is a 0.12mm Japanese steel BGA reballing stencil with square holes for Qualcomm WiFi and audio ICs. One plate covers WCN3680, WCN3660, WCN3620, WCN3615, WCN3980 and WCN3990 on the WiFi side, plus WCD9340, WCD9341, WCD9335, WCD9326, WCD9330, WCD9320, WCD9310, WCD9304, WCD9302 and WCD9306 on the audio side. The super hard sheet holds its aperture shape across repeated heat cycles, so you reball clean, even balls job after job. Mechanicpk offers it to repair shops and technicians who want one spec-matched template for Qualcomm WCN and WCD rework on the bench.

In stock

11 People watching this product now!
Description

Amaoe WC1 Reballing Stencil for Qualcomm WCN and WCD ICs

The Amaoe WC1 reballing stencil gives you one 0.12mm steel template for a broad run of Qualcomm WiFi and audio codec ICs, from WCN3680 and WCN3660 through WCN3990 and WCD9341. Mechanicpk offers it to technicians who handle WCN and WCD work often and want one stencil on the bench instead of a drawer of single-chip templates. The WC1 pairs Japanese steel sheet with square apertures, so solder balls or paste sit square on the pads when you reball a lifted IC.

Construction and Hole Geometry

Amaoe cuts the WC1 from Japanese steel sheet at 0.12mm thickness and rates the steel super hard. That thickness suits fine-pitch WCN and WCD packages, where a thicker plate would deposit oversized balls and risk bridging between pads. The square holes give each ball or paste deposit a defined footprint, and the stiff sheet resists the bending that ruins softer templates after a few heat cycles.

Amaoe lists the stencil as reusable, so one plate serves many jobs across a busy week. Clean it with flux remover and a soft brush after each use to keep the aperture edges sharp. Hold it flat on a PCB holder or magnetic reballing base while you work, because a lifted corner shifts the ball pattern and costs you a second attempt.

Supported WCN and WCD Chips

The WC1 layout covers two chip families. On the WiFi side, it handles WCN3680, WCN3660, WCN3620, WCN3615, WCN3980 and WCN3990. On the audio codec side, it handles WCD9340, WCD9341, WCD9335, WCD9326, WCD9330, WCD9320, WCD9310, WCD9304, WCD9302 and WCD9306.

Match the marking on your IC against this list before you start, because a stencil only works when its ball pattern matches the package exactly. The WC1 list contains WCN and WCD parts only, so keep Qualcomm CPU and power management work on dedicated stencils for those packages. Buy the WC1 when your repair queue mixes WiFi and audio faults on Qualcomm boards, since one plate replaces several single-chip templates and keeps your bench organised.

Reballing Workflow and Repair Fit

A typical WC1 job starts with hot air removal of the faulty IC. Clean the pads with flux and solder wick, fix the chip in place, align the stencil over the ball pattern, then apply paste or place tin balls. Heat evenly until the balls form, lift the stencil after it cools, and inspect the result under a microscope before you seat the IC back on the board.

WiFi IC change karna jobs follow exactly this routine. A phone with a hardware fault in the wireless section, such as WiFi greyed out or a network issue you trace to the WCN chip, comes back to life only when the replacement or reballed IC sits on clean, even balls. Audio codec work on WCD parts follows the same steps when you trace a sound fault to the codec.

Keep a multimeter beside you to check for shorts around the pads, and use a hot air station with controlled airflow so neighbouring components stay safe. If you reball other IC types as well, pair the WC1 with a complete reballing kit and a stable soldering station so every job runs through the same proven process.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • 0.12mm stencil thickness for fine-pitch WCN and WCD packages
  • Japanese steel sheet construction
  • Super hard steel resists bending across heat cycles
  • Square hole design for defined ball and paste placement
  • Reusable stencil for repeated reballing jobs
  • Covers six WCN WiFi ICs and ten WCD audio codec ICs on one plate
  • Replaces several single-chip templates on a busy bench
  • Fits a standard hot air reballing workflow

Specifications

BrandAmaoe
ModelWC1
CategoryBGA Reballing Stencil
CompatibilityQualcomm WCN WiFi ICs and WCD audio codec ICs (chip-level, not device-specific)
Supported DevicesBoards carrying the Qualcomm WCN and WCD ICs listed below
TechnologyBGA reballing stencil, 0.12mm thickness, square holes, super hard steel
MaterialJapanese steel sheet

Common Repair Uses

  • Reballing and replacing Qualcomm WiFi and audio codec ICs at board level.
  • Reballing a lifted WCN WiFi IC before refitting it
  • Replacing a faulty WCN IC when WiFi stays greyed out or will not switch on
  • Fixing a hardware fault in the wireless section that causes a network issue
  • Reballing a WCD audio codec IC after removal
  • Tracing and correcting a sound fault that points to the audio codec
  • Re-tinning pads after lifting an IC with hot air
  • Reballing a good donor IC for reuse on another board
  • Training junior technicians on fine-pitch BGA reballing

Compatible Devices

  • Chip-level scope — any Qualcomm-based board that carries one of these WCN or WCD ICs. The stencil fits the IC package, not a specific phone model.
  • WCN3680 / WCN3660 WiFi ICs
  • WCN3980 WiFi IC
  • WCN3990 WiFi IC
  • WCN3620 / WCN3615 WiFi ICs
  • WCD9340 / WCD9341 audio codec ICs
  • WCD9335 / WCD9326 audio codec ICs
  • WCD9330 / WCD9320 / WCD9310 audio codec ICs
  • WCD9304 / WCD9302 / WCD9306 audio codec ICs

FAQ

What is the product name?
The product name is Amaoe WC1 Reballing Stencil for Qualcomm WCN/WCD ICs.
What is the brand of this product?
The brand of this product is Amaoe.
What is the model of this product?
The model of this product is WC1.
What is this product used for?
This product is used for reballing Qualcomm WCN WiFi ICs and WCD audio codec ICs at board level.
Which devices are compatible with this product?
This product fits the IC packages listed for Qualcomm WCN and WCD chips, so it works on any board that carries those ICs. It is not tied to a single phone model.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which Qualcomm WiFi and audio ICs does the Amaoe WC1 stencil cover?
It covers WCN3680, WCN3660, WCN3620, WCN3615, WCN3980 and WCN3990 WiFi ICs, plus WCD9340, WCD9341, WCD9335, WCD9326, WCD9330, WCD9320, WCD9310, WCD9304, WCD9302 and WCD9306 audio codec ICs.
What thickness and hole type does the Amaoe WC1 stencil use?
The WC1 uses a 0.12mm Japanese steel sheet with square holes, and Amaoe rates the steel super hard and reusable.