2UUL MT01 Multimeter Pens – Gold-Plated 1000V Probes
₨ 1,500
Fine-Tip Multimeter Pen for PCB Testing
The 2UUL MT01 gives you a 0.2mm gold-plated needle tip on a 1000V-rated pen built for mobile motherboard diagnostics. Stainless steel needles with gold plating keep contact resistance low, and you swap a worn needle instead of replacing the whole probe. Flame-retardant, high-temperature-resistant silicone insulation stays soft in cold workshops, and the non-slip grip holds steady through long board-level sessions. A dust protection plug covers the interface between jobs. The standard banana plug fits most digital multimeters, so you probe charging lines, test points, and SMD pins on dead phone boards without extra adapters.
In stock
Multimeter Pen for Mobile Repair: 2UUL MT01 Fine-Tip Probes
A multimeter pen for mobile repair decides how clean your readings are on a crowded board, and the 2UUL MT01 puts a 0.2mm gold-plated needle on every contact you probe. Mechanicpk supplies this pair to Pakistani repair shops that diagnose dead phone boards, charging line faults, and SMD component failures every day. The stainless steel tip carries a gold plating layer for low internal resistance, and the insulating silicone body stays soft instead of stiffening with age. You plug the leads into any digital multimeter that takes a standard banana plug and start measuring pads, test points, and component pins straight away.
Tip Design and Contact Quality
The 0.2mm needle fits between densely packed pads where a stock probe slips or bridges two contacts. You land the point on a single component pin, hold it steady, and read voltage or continuity without scraping the neighboring solder mask. Gold plating over stainless steel resists oxidation, so contact resistance stays low across long sessions on the bench. The tip carries a 1000V rating, and the needle replaces cleanly: when a point bends or wears after heavy use, you swap the needle and keep the same handle and cable. That approach keeps your cost per repair low compared with buying a full probe set every time a tip fails.
Insulation, Grip, and Durability
The silicone body resists flame and high temperature, so it handles the heat around your rework area better than a stiff PVC lead. It also resists freezing and does not harden, which keeps the cable flexible in a cold workshop during winter. The non-slip grip lets you hold the pen like a pencil through long diagnostic sessions without hand fatigue, and the soft silicone cushions your fingers instead of cutting into them. A dust protection plug covers the interface when you store the pen, which stops dust and oxidation from building up on the connector between jobs.
Where the MT01 Fits in Your Repair Workflow
Use the MT01 early in the diagnostic process. When a phone arrives with a charging issue or dies after a short, you probe the charging line, battery connector pins, and test points to locate the fault before you touch the board with a soldering iron. After you find a broken track, you trace continuity from end to end and decide where to jumper lagana. When you finish an IC change karna job, the same pen confirms that each pin reads correctly before you power the board.
The pen pairs with the tools already on your bench. Hold the board in a PCB holder, inspect fine pads under a microscope, and run your multimeter in continuity or diode mode while you probe. Technicians who work on reballing and BGA jobs rely on pin-level continuity checks, and the MT01 delivers that precision. Browse the Multimeters, Microscopes, PCB Holders, Soldering Stations, Hot Air Stations, Reballing Kits, and Test Boxes categories at Mechanicpk to build a complete diagnostic bench around this multimeter pen for mobile repair.
| Weight | 0.2 kg |
|---|
Key Features
- ✓0.2mm needle tip reaches single pads and component pins on dense boards
- ✓1000V rated probe tip
- ✓Stainless steel needle with gold plating for low internal resistance
- ✓Replaceable needle tip extends the life of the handle and cable
- ✓Flame-retardant, high-temperature-resistant silicone insulation
- ✓Freeze-resistant silicone that does not harden in cold workshops
- ✓Non-slip silicone grip for steady, comfortable handling
- ✓Dust protection plug protects the interface from dust and oxidation
Specifications
| Brand | 2UUL |
|---|---|
| Model | MT01 |
| Category | Multimeter Test Probes / Multimeter Accessories |
| Compatibility | Digital multimeters with standard banana plug input |
| Technology | 0.2mm gold-plated needle tip, replaceable needle, 1000V rated |
| Material | Gold-plated stainless steel tip, silicone insulation |
Common Repair Uses
- ✓Board-level voltage, continuity, and pin testing during mobile phone diagnostics
- ✓Checking voltage on charging lines and test points
- ✓Testing continuity on battery connector pins
- ✓Probing individual SMD component pins and pads
- ✓Locating short circuits on dead phone boards
- ✓Tracing broken tracks before you place a jumper
- ✓Reading diode mode values around connectors and ICs
- ✓Verifying pin continuity before and after an IC change
- ✓Checking BGA and reballed IC pins for continuity
Compatible Devices
- ✓Universal — works with any digital multimeter that accepts a standard banana plug, and probes motherboards of any phone brand (not device-specific)
- ✓Digital multimeters with standard banana plug input
- ✓Universal multimeters used on repair benches
- ✓Samsung phone motherboards
- ✓Apple iPhone logic boards
- ✓Xiaomi phone motherboards
- ✓Huawei phone motherboards
- ✓Motorola phone motherboards
- ✓Google Pixel and Sony phone boards



