Relife RL-727 3D Extreme Edition Screwdriver Set
₨ 2,000
Relife RL-727 3D Screwdriver for Precision Mobile Repair
The Relife RL-727 3D Extreme Edition packs three imported S2 steel bits into one handle: Y 0.6, Phillips 1.5, and Pentalobe 0.8. The 3D tip profile is designed to seat fully in the screw recess, which reduces cam-out and stripped heads on small fasteners. A built-in magnetizing block holds screws on the tip during removal, so nothing drops inside a housing. The handle uses high-hardness aviation aluminum with an anti-slip finish, and the precision silent bearing keeps the turn smooth under downward pressure. Use it for back covers, shield screws, and board-level access on your repair bench.
In stock
Relife RL-727 3D Extreme Edition Screwdriver for Mobile Phone Repair Workflows
The Relife RL-727 3D screwdriver belongs at the start of most phone disassembly jobs. Your workflow begins with removing back covers, display shields, and internal housing screws, and this set covers the three head types you meet most often on those fasteners. You switch bits without changing the handle. The 3D Extreme Edition tip aims for full contact with the recess, so the bit grips the screw head instead of riding up and chewing it. That fit protects small screws through repeated opening and reassembly at the bench, which is where most stripped-head problems start.
Bit Set and Head Profiles
The set ships with three imported S2 steel bits: Y 0.6, Phillips 1.5, and Pentalobe 0.8. S2 is a tool steel known for toughness, so the tip keeps its edge when you apply firm torque to a stubborn fastener. The Y 0.6 bit addresses the three-lobed recesses used on certain phone and electronics assemblies. The Phillips 1.5 handles small cross-head screws in older housings and modules. Pentalobe 0.8 covers the five-lobe fasteners common on compact devices. Check the head on your device before you start, because the right bit protects the screw far better than extra force does. Keep all three bits together in your toolkit so none goes missing mid-job.
Magnetizing Block and Silent Bearing
The built-in magnetizing block charges the bit with permanent magnetic strength. The screw stays on the tip when you lift a housing, which matters for a 0.6 mm Y screw that can vanish inside a case or under the bench mat. The magnet also holds the fastener steady while you start the thread, so you spend less time chasing it. The precision silent bearing sits in the rotating nut and is designed to let the handle turn smoothly under downward pressure. That smooth turn reduces the wobble that pushes a bit out of the head. Your hand stays steadier through a long shift of back covers and board screws.
Handle Ergonomics and Care
The handle body uses high-hardness aviation aluminum, which keeps the grip rigid so your pressure reaches the bit rather than flexing in the shaft. The anti-slip finish helps when your hands are sweaty or when you work through a hot afternoon. Grip the handle near the fingers rather than the cap, since that keeps your alignment straight over the screw. The 3D tip design aims for a full seat in the recess, so the bit keeps contact without constant correction. After each shift, wipe the bits, dry the steel, and store the set in a dry box away from humidity. That protects the aluminum finish and keeps the bit seats clean for the next dead phone on your bench.
| Weight | 0.3 kg |
|---|
Key Features
- ✓3D Extreme Edition tip profile for full recess contact
- ✓Three imported S2 steel bits: Y 0.6, Phillips 1.5, Pentalobe 0.8
- ✓Built-in magnetizing block for permanent tip magnetism
- ✓Precision silent bearing for smooth handle rotation
- ✓High-hardness aviation aluminum handle body
- ✓Anti-slip grip finish for steady control
- ✓Compact set for toolkit storage and bench use
- ✓Suitable for disassembly and maintenance of telecom and electronic equipment
Specifications
| Brand | Relife |
|---|---|
| Model | RL-727 (3D Extreme Edition) |
| Category | Screwdrivers for mobile repair |
| Compatibility | Universal, not device-specific |
| Supported Devices | Mobile phone and small electronics fasteners matching the Y 0.6, Phillips 1.5, and Pentalobe 0.8 heads |
| Technology | 3D tip profile, built-in magnetizing block, precision silent bearing |
| Material | Imported S2 steel bits, high-hardness aviation aluminum handle |
Common Repair Uses
- ✓Real bench workflows where these three heads and the magnetic tip apply
- ✓Removing rear housing screws during battery replacement
- ✓Opening display shield and assembly screws before LCD or OLED work
- ✓Disassembling phone frames for board-level diagnosis
- ✓Reassembling housings with screws held on the magnetized bit
- ✓Removing shield or module fasteners before charging port or IC work
- ✓Opening small electronics housings during bench service
- ✓Teardown of a dead phone to reach the mainboard
- ✓Tightening screws during final reassembly without overtightening
Compatible Devices
- ✓Universal scope, verified by head type rather than specific phone model
- ✓Y 0.6 head for Y-type recess fasteners on phone and electronics assemblies
- ✓Phillips 1.5 cross head for small cross-head screws in phone and module housings
- ✓Pentalobe 0.8 head for five-lobe fasteners on compact electronics
- ✓Mobile phone disassembly for general housings (match the head type on your device)
- ✓Small electronics housings and modules that use the three head profiles above
- ✓Telecommunications and electronic equipment, as stated in the manufacturer description
- ✓Mechanical fastener tool, not chipset-based
- ✓Universal, not device-specific: confirm the head type on each screw before use



