Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
₨ 1,500
Qianli 011 16-in-1 Glue Removal Knife
The Qianli 011 is a glue removal knife for mobile repair that gives you a handle with hand-polished, replaceable blades in a 16-in-1 multi-function format. You use it to strip glue and separate chips on phone boards before hot air rework, IC change karna jobs, and reballing. The universal design works across brands, so one tool covers glued ICs on every board that reaches your bench. Order the Qianli 011 from Mechanicpk and keep a dependable first-step tool beside your hot air station, microscope, and PCB holder.
Out of stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
A glue removal knife for mobile repair decides how cleanly you reach the chip underneath. The Qianli 011 16-in-1 multi-function glue removal knife gives you one handle with hand-polished, replaceable blades built to remove glue and separate chips on phone boards. You cover black glue, sealed IC edges, and stubborn adhesive with a single tool, so your repair bench needs fewer single-purpose scrapers. Technicians in Pakistan reach for this knife before every IC change karna job, because glue left around a chip leads to lifted pads and uneven heat during rework. This page covers what the knife does, where it fits in your workflow, and how to use it without damaging the board.
Where the Qianli 011 Fits in Your Repair Workflow
Adhesive removal sits between diagnosis and rework. Once you confirm a hardware fault such as a dead phone, a charging issue, or a hang on logo, you expose the suspect IC and clear the glue around it. The Qianli 011 handles that step. You warm the board on your hot air station or preheater, run the blade along the glue line, and lift the residue away before you touch the chip. A clean perimeter lets hot air reach the solder balls evenly and lets you see every pad under your microscope. When the glue is gone, you move on to chip removal, pad cleaning, and reballing with your BGA reballing kit. Shops that handle high volumes of dead after flash and hardware fault boards benefit most, because every minute saved at the glue stage adds up across a day of repairs. Work under good magnification and keep the board supported on a PCB holder so the knife never slips toward nearby components.
Hand-Polished Blades in a Multi-Function Format
Qianli builds the 011 around hand-polished blades with hard, resilient quality. The 16-in-1 format pairs one handle with multiple blades, so you match the blade to the glue line you face instead of forcing one edge into every gap. Replaceable blades keep the tool working long term, and Qianli supplies replacement blades for the 011, so a worn edge costs you a blade rather than a whole tool. Hold the blade flat against the board, use short controlled strokes, and let the edge do the cutting. That technique protects neighbouring capacitors, shield cans, and flex connectors while you work. Check the blade edge before each job. A clean, undamaged edge cuts adhesive with less force, which reduces the chance of a slip. Swap the blade once the edge stops cutting cleanly rather than pressing harder. Because the tool is universal and not tied to one phone model, the same knife serves every glued board on your bench.
Using the Qianli 011 Glue Removal Knife Before IC Work
The Qianli 011 glue removal knife earns its place whenever sealed chips block your next step. Before an eMMC or UFS replacement, you clear the glue around the package so your hot air nozzle lifts the chip without dragging adhesive across the pads. Before CPU or power IC work, you cut back the black glue so you reach every edge of the BGA. During ISP work, you remove adhesive over test points so your probes or pogo pins sit flat. Keep the board warm but never overheat it, since the aim is to soften the glue without cooking nearby components. Work in small sections and clear residue between passes so you always see what the blade touches. Pair the knife with a PCB holder for stability, flux for clean pad work, and a soldering station for finishing. If your shop needs a wider blade assortment, explore the other Qianli knife and blade sets in the Mechanicpk repair accessories range.
| Weight | 0.9 kg |
|---|
Key Features
- ✓16-in-1 multi-function glue removal design
- ✓Hand-polished blades for a sharp, smooth edge
- ✓Hard, resilient blade quality
- ✓Handle with replaceable blades
- ✓Replacement blades available for the 011
- ✓Removes glue and separates chips on phone boards
- ✓Universal use across phone brands
- ✓Fits alongside hot air stations, microscopes, and PCB holders
Specifications
| Brand | Qianli |
|---|---|
| Model | 011 (16-in-1 Multi-Function) |
| Category | Glue Removal Knives / Mobile Repair Hand Tools |
| Compatibility | Universal, not device-specific |
| Supported Devices | Universal, mobile phone boards |
| Technology | Hand-polished blades with replaceable blade design |
Common Repair Uses
- ✓Removing black glue around BGA ICs before hot air removal
- ✓Separating chips from the board during IC change karna jobs
- ✓Clearing adhesive around eMMC and UFS packages before replacement
- ✓Exposing CPU and power IC edges for dead phone diagnosis
- ✓Cleaning glue residue from pads before reballing
- ✓Clearing adhesive over ISP test points before probing
- ✓Preparing glued boards for hardware fault inspection under a microscope
- ✓Disassembling glued components during board-level repair
Compatible Devices
- ✓Universal tool with no device-specific limit. It works wherever glue covers or seals a chip.
- ✓Universal mobile phone mainboards with glue-sealed ICs
- ✓Boards with black glue around BGA chips
- ✓Logic boards with adhesive-covered eMMC and UFS packages
- ✓Boards with sealed CPU and power IC edges
- ✓Boards with glued shield and component perimeters
- ✓Any phone board needing chip separation before hot air rework
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can the Qianli 011 remove black glue around BGA chips before eMMC or CPU replacement?
Can you replace the blades on the Qianli 011?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



