MECHANIC FXV08 3 in 1 Fine Silver Flying Line 0.008mm

₨ 2,999

0.008mm Fine Silver Flying Line for CPU and Trace Jumper Repair

Your repair bench needs a jumper that lays flat on a broken trace without crowding the pads beside it. The MECHANIC FXV08 gives you a 500m spool of 0.008mm fine silver flying wire, bundled as a 3 in 1 set with a pure copper welding head. Use it to bridge CPU breakpoints, reconnect cut motherboard traces, and fix screw-hole short circuits on mobile phone PCBs. Thin wire keeps the board flat for reassembly, and one spool covers many jobs because each repair consumes only a few centimeters. Keep this line on the bench when a dead phone comes down to one missing trace.

In stock

17 People watching this product now!
Description

Fine Silver Flying Line 0.008mm for Mobile Motherboard Repair

A fine silver flying line 0.008mm becomes essential when a trace breaks beyond what a standard jumper can reach. On a mobile PCB, you work at the level of single pads and hairline copper, so wire thickness decides whether your repair seats flat or lifts a neighboring component. The MECHANIC FXV08 closes that gap with a 500m spool and a matched copper welding head. Its diameter sits well below the width of most mobile board traces, so you can route a jumper through tight layouts without bridging adjacent lines. Your bench gains a dedicated tool for point-to-point repair, not a makeshift wire pulled from a cable. The sections below cover where this wire fits in your workflow, how to handle it under a microscope, and how to stock the 3 in 1 set for daily repair volume.

Where Fine Silver Flying Wire Fits in the Repair Workflow

Board-level repair follows a clear sequence. You start with diagnostics, using a multimeter for continuity and a microscope for visual inspection. Once you confirm an open trace or a lifted pad, you move to the jumper stage and select the wire before you touch the iron. This 0.008mm line handles CPU breakpoints, cut traces near connectors, and short paths left after screw-hole damage. It does not replace BGA reballing or hot air reflow, because it finishes the job those steps leave open. Pair the wire with a microscope, flux, and a fine-tip iron to complete the full routing cycle. Treat it as the final connection step on a board that already has clean pads and correct component placement.

Handling 0.008mm Silver Wire Under the Microscope

Precise handling decides whether a jumper holds. Work under a microscope with clean tweezers, and secure the board firmly so it does not shift while you solder. Tin the pad first so solder flows onto the metal before the wire lands. Lay the wire across the break, tack one end, pull it taut, and then tack the other end. Trim the excess close to the joint so no loose strand touches an adjacent pad. Keep hot air exposure short near sensitive ICs, because repeated heating can damage nearby components that the repair never touched. Store the spool in a dry drawer away from heat, since loose wire tangles quickly on a crowded bench and wastes time you cannot recover.

Stocking the 3 in 1 Set for Daily Board Repair

The 3 in 1 set bundles the wire spool with a pure copper welding head, so you do not need to match a tip to the spool yourself. A 500m spool supplies many repairs from one purchase, since each board consumes only a few centimeters. Plan your stock by job frequency rather than by meter count. In a busy repair shop, CPU breakpoints, trace repairs, and screw-hole faults appear regularly, so keep the spool beside your flux and BGA stencils. Track how many jobs each spool supports over a month, then set reorder points from that count. This approach keeps your jumpers within reach and prevents a delayed repair caused by an empty drawer.

Additional information
Weight0.4 kg
Q & A
Please login to post questions

Key Features

  • 0.008mm diameter fits tight pads and narrow trace gaps
  • 500m spool supplies many repairs from one purchase
  • Fine silver wire sits flat on the board surface
  • Matched pure copper welding head included in the 3 in 1 set
  • Works under a microscope for precise jumper placement
  • Suits CPU breakpoint and cut trace repair
  • Supports fingerprint flex line and screw-hole fault repair
  • Routes jumpers without adding bulk to the board

Specifications

BrandMECHANIC
ModelFXV08
CategoryMobile Soldering Accessories
CompatibilityUniversal, not device-specific
Supported DevicesMobile phone and tablet motherboards at trace and pad level
TechnologyFine silver flying wire, 0.008mm diameter
Length500m spool
Weight0.4 kg

Common Repair Uses

  • CPU chip breakpoint jumpers
  • Cut motherboard trace bridging
  • Screw hole short circuit repair
  • Fingerprint flex line trace rebuilding
  • Dead after flash data line jumpers
  • Charging line trace reconnection
  • Network signal trace repair near the RF section
  • BGA rework support during board reconnection

Compatible Devices

  • Universal, not device-specific: applies to any mobile phone motherboard
  • Smartphone PCB trace repair at component level
  • Tablet motherboard trace and pad repair
  • CPU chip breakpoint repair on mobile boards
  • BGA chip pad and trace reconnection
  • Flex cable trace repair near connectors
  • Screw-hole short circuit trace repair
  • Charging and data line trace jumpers

FAQ

What is the product name?
The product name is MECHANIC FXV08 3 in 1 Fine Silver Flying Line 0.008mm.
What is the brand of this product?
The brand of this product is MECHANIC.
What is the model of this product?
The model of this product is FXV08.
What is this product used for?
This product is used for bridging broken CPU points, reconnecting cut motherboard traces, and fixing screw-hole short circuits on mobile phone PCBs.
Which devices are compatible with this product?
This product is compatible with any mobile phone or tablet motherboard at the trace and pad level. It is not device-specific.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Which wire thickness suits CPU breakpoint jumpers?
A 0.008mm line suits fine pads and narrow traces, because thicker wire cannot sit flat between tight layout gaps.
Does 0.008mm wire work for fingerprint flex trace repair?
Yes, the 0.008mm line can rebuild broken fingerprint flex traces, provided you work under a microscope and tin the pad before placing the wire.