Sunshine SS-051 0.03mm OLED Screen Separation Wire

₨ 400

Sunshine SS-051 Tungsten Alloy Separation Wire

The Sunshine SS-051 is a 0.03mm tungsten alloy steel wire made for thermal separation of OLED edge screens. Its fine diameter fits the narrow gap along the display edge, and its forged construction holds up under tension during the pull. Each package carries 100 meters of wire, and you can choose a single piece or a 5-piece pack. Reach for this wire when your workflow calls for controlled, precise separation instead of fast, rough lifts. Technicians handling screen replacement and display rework will find it a dependable addition to the bench.

Out of stock

18 People watching this product now!
Description

OLED Screen Separation Wire 0.03mm for Precise Edge Work

An OLED screen separation wire 0.03mm in diameter lets you lift a display from its frame with less stress on the panel. The Sunshine SS-051 is a tungsten alloy steel wire built for thermal separation, where heat softens the adhesive along the screen edge and the wire follows that glue line. Each package gives you 100 meters of wire, which covers a long run of separations before you need a restock. This article explains what the wire does on your repair bench, how its diameter and construction affect the cut, and how to set it up for OLED edge work.

Why a 0.03mm Diameter Suits Fine Separation Work

The diameter of a separation wire decides how much clearance it needs when it passes between the display and the frame. A 0.03mm line is fine enough to slip into the narrow gap along an OLED edge without forcing the panel apart. Thicker wire moves more slowly through the adhesive and applies more pressure to the glass, which raises the risk of cracks and creases. This gauge keeps the cut line thin and controlled, so the adhesive releases with less stress on the panel. You get a predictable path because the wire stays close to the edge rather than biting into the display. On a busy repair bench, a fine gauge reduces the number of failed separations that cost you a screen. Choose this diameter when the screen is expensive, the edge is tight, and precision matters more than speed. Both the 1-piece and 5-piece packages use the same 0.03mm wire, so you can keep a backup on hand without changing your setup.

Tungsten Alloy Build, Length, and Long-Run Durability

Sunshine SS-051 uses a tungsten alloy steel wire with a forged construction for strength. The toughness of the forged core helps it hold tension through repeated thermal passes, which matters when the adhesive resists and the wire must pull harder. A wire that snaps mid-separation wastes time and can damage the panel edge, so tensile reliability directly affects your success rate. Each spool measures 100 meters, which supports a long run of separations without frequent swaps. Longer spools also mean fewer interruptions when you work through a batch of OLED screens. Keep the wire clean and unspool it gently to avoid kinks that can weaken the line. Steady tension and a durable core together make the difference between a clean lift and a costly restart.

Using OLED Screen Separation Wire on the Bench

Begin by securing the device and preparing your heat source according to your usual OLED thermal separation routine. Heat the screen edge evenly so the adhesive softens before the wire enters the gap. Route the wire along the edge with light, steady tension, letting it move through the glue line without forcing it sideways. Work slowly around corners, where the wire experiences the most pull and where the panel is most vulnerable. Check the edge as you progress, watching for stress marks, lifting, or uneven release. If the wire drags, pause, reheat the section, and resume rather than increasing force. Once the adhesive releases along the full edge, lift the panel gradually and keep the glass free of bending. Clean the frame and remove any residue before you fit a new display so the replacement sits flat.

Additional information
Weight0.1 kg
Q & A
Please login to post questions

Key Features

  • 0.03mm diameter for fine separation lines
  • Forged tungsten alloy steel construction
  • Designed for thermal separation of OLED edge screens
  • 100m spool length per package
  • Available in 1-piece or 5-piece packages

Specifications

BrandSunshine
ModelSS-051
CategoryScreen Separation Wire
TechnologyThermal separation
MaterialTungsten alloy steel
CompatibilityUniversal, not device-specific (OLED and LCD screen separation)
Supported DevicesOLED edge screens (thermal separation)
Dimensions0.03mm diameter, 100m length

Common Repair Uses

  • Lifting OLED screens from the frame during panel replacement
  • Controlled separation along a tight display edge
  • Thermal separation workflow on screen rework

Compatible Devices

  • Universal, not device-specific. Scope covers OLED and LCD screen assemblies.
  • OLED edge screens for thermal separation
  • LCD screen assemblies for separation work

FAQ

What is the product name?
The product name is Sunshine SS-051 0.03mm OLED Screen Separation Wire.
What is the brand of this product?
The brand of this product is Sunshine.
What is the model of this product?
The model of this product is SS-051.
What is this product used for?
This product is used for thermal separation of screen edges from the frame during display replacement.
Which devices are compatible with this product?
This product is compatible with OLED and LCD screen separation work. It is universal and not device-specific.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
What diameter is this separation wire?
The wire measures 0.03mm in diameter, which suits fine separation work along tight screen edges.
Is this wire suitable for OLED screen separation?
Yes. The wire is built for thermal separation of OLED edge screens.