2UUL DA83 Plier Cutter for Phone Repair
₨ 950
2UUL DA83 Plier Cutter for Phone Repair
The 2UUL DA83 plier cutter is a compact, spring-loaded diagonal cutter for mobile phone and PCB repair benches. Its hardened cutting edge trims jumper wire, component leads, cables and plastic ties cleanly, and the anti-slip rubber-sleeved handle keeps your grip steady through long sessions. Technicians use it for board-level jumper work, cable trimming and frame disassembly on dead phone, charging issue and hardware fault jobs. Mechanicpk supplies the DA83 to repair shops across Pakistan that want a dependable hand cutter beside their soldering station and microscope. The package includes one plier.
Out of stock
2UUL DA83 Plier Cutter: Compact Diagonal Cutter for Board-Level Work
The 2UUL DA83 plier cutter gives your bench a small diagonal cutter built around the cuts a mobile technician makes every day: jumper wire, component leads, cables and plastic ties. It belongs to the 2UUL hand-tool range, which targets phone and PCB repair rather than general electrical work. Mechanicpk supplies it to workshops and service centers in Pakistan that already run a soldering station, hot air station and microscope and need a dependable cutter to complete that setup. Precision electronics work rewards a tool sized for the job, and the DA83 keeps its jaws, handle and weight matched to small-scale board repair.
Jaw and Handle Design
The DA83 uses a diagonal cutting head with a hardened cutting edge. Hardening helps the edge stay sharp across repeated cuts on thin copper wire, so you get a clean snip instead of a crushed or frayed lead. A spring-loaded action opens the jaws after each cut, which frees your other hand to hold the board, a pair of tweezers or a PCB holder. The rubber-sleeved handle resists slipping, and the handle position reduces hand fatigue when you cut repeatedly across a long repair shift. The compact body slips into the tight gaps around a phone motherboard and stores easily in a tool pouch or on a bench tray.
Where the DA83 Fits in the Repair Workflow
Many hardware fault repairs end with a jumper lagana step: you bridge a damaged trace with a thin wire, then trim the excess. The DA83 handles that trim. On a dead phone or a charging issue board, you cut the jumper wire to length, solder it under the microscope and verify the circuit with a multimeter. After a component swap, you trim long leads before testing. During disassembly, the same cutter handles cables, tape and plastic ties, and supplier documentation lists screen frame, camera and motherboard component cutting among its uses. Treat it as a general-purpose small cutter for the repair bench, and pair it with fine tweezers, flux and a reballing kit so every cut-and-solder step stays on one workstation.
What to Check Before You Buy
Match the cutter to the material. The DA83 suits thin copper wire, component leads, insulating sleeves, cable ties and similar light material found on phone boards and frames. Keep it away from thick steel wire, nails and hard metal, because heavy loads damage a precision cutting edge and shorten its working life. Technicians who run high-volume repair counters often keep two or three cutters on the bench so one is always at hand during busy hours. The package contains a single plier, so order extra units if your team shares one workstation. If you plan to expand your hand-tool range, add tweezers, PCB holders and screwdrivers from the same 2UUL line to keep your bench consistent.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Diagonal cutting head for clean, close cuts on thin wire and leads
- ✓Hardened cutting edge for sharp, repeatable cuts
- ✓Spring-loaded action returns the jaws to open after each cut
- ✓Rubber-sleeved handle with anti-slip grip
- ✓Handle position shaped to reduce hand fatigue during long sessions
- ✓Compact body for tight spaces around phone boards
- ✓Suits wire, cables, ties, sleeves and light plastic cutting
- ✓Package includes 1 plier
Specifications
| Brand | 2UUL |
|---|---|
| Model | DA83 |
| Category | Cutters / Hand Tools |
| Compatibility | Universal — not device-specific |
| Technology | Spring-loaded diagonal cutting action |
Common Repair Uses
- ✓Jumper wire trimming, component lead cutting, cable and tie cutting during disassembly
- ✓Trimming jumper wire after trace repair
- ✓Cutting excess component leads after soldering
- ✓Cutting cables during phone disassembly
- ✓Trimming insulating sleeves
- ✓Cutting nylon cable ties and tape
- ✓Trimming screen frame sections during separation
- ✓Removing small unwanted parts from the board edge
- ✓General bench cutting in dead phone and charging issue jobs
Compatible Devices
- ✓Universal hand tool — not device-specific; suits any smartphone board or frame where thin wire, leads or plastic need cutting
- ✓Smartphone motherboards (jumper wire and lead trimming)
- ✓Phone middle frames
- ✓Screen frame assemblies
- ✓Camera module cables and wiring
- ✓Shield covers and thin board-mounted metal parts (light trimming)
- ✓Android phone repair boards
- ✓iPhone repair boards
- ✓Tablet and small-electronics PCBs
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What materials can the 2UUL DA83 cut on a phone repair bench?
Is the 2UUL DA83 a diagonal cutter, and does it suit jumper wire work?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



