MiJing C17 3in1 Main Board Test Fixture iPhone X/XS/Max
₨ 1
MiJing C17 Layered Test Fixture
The MiJing C17 motherboard test fixture gives you a 3-in-1 layered platform for function testing iPhone X, iPhone XS and iPhone XS Max logic boards. You stack the lower board, pin board and upper board inside the fixture, then check screen, boot, power and battery response before final assembly. A second connection route through the base end plug adds a flashing function to the same setup. Pakistani repair shops use middle-layer fixtures like this to catch dead phone and no-power faults early, protect reflowed boards from repeated disassembly and keep the repair bench moving.
Out of stock
MiJing C17 Motherboard Test Fixture for iPhone X, XS and XS Max Logic Boards
The MiJing C17 motherboard test fixture targets a problem every iPhone X-series technician knows: a two-layer logic board only shows its true condition once it powers up. Reassembling the middle frame just to learn that the board still dead-boots wastes time and stresses solder joints you already reworked. The C17 lets you power and test the stacked board outside the chassis, so you confirm the fault is fixed before you close the phone. The fixture covers three models in one unit: iPhone X, iPhone XS and iPhone XS Max.
How the C17 3-in-1 Layered Design Works
The C17 holds the lower main board, a pin board and the upper main board in one test rack. You seat the lower board first, set the pin board over it, drop the upper board on top and cover the rack. The pin board bridges the two layers, so the board stack behaves electrically as it would inside the middle frame. This layered structure is what makes the C17 an iPhone X middle layer test fixture rather than a simple board holder.
The 3-in-1 label means one fixture handles the X, XS and XS Max boards. A shop that services all three models saves bench space and avoids buying a separate stand for each. Because you test the board before installing it, you avoid the repeated teardown that causes virtual soldering, CPU tin damage and lifted pads after rework.
Two Connection Methods for Testing and Flashing
Prepare the following before you start: a power on/off cable, a power line, an LCD test cable, a screen and the main board you want to test.
The first connection method links the screen cable, the boot cable, the power cord or a battery. You then watch whether the board boots and the display responds. A pass here tells you the board is healthy. A failure points you back to the board before you waste a screen or a battery on it.
The second method builds on the first. You connect the end plug on the base of the fixture to enable the flashing function. If a board hangs on logo or dies after a software operation, you can handle it on the same fixture without moving it to a separate stand.
Where It Fits in Your iPhone X-Series Repair Workflow
The C17 sits at the verification stage of board-level repair. After you replace an IC, reball a chip or repair a trace, you place the stack in the fixture and run the power and screen checks. Pair it with a multimeter for rail checks, a microscope for joint inspection and a PCB holder for rework. Technicians who reflow boards with a hot air station or soldering station often keep the fixture beside the station, so every rework gets a quick function test before the board returns to the chassis.
For a charging issue, display problem or no-power fault, the fixture helps you separate board faults from peripheral faults. You swap the screen or battery on the fixture in seconds and see which part causes the symptom.
Choosing the Right MiJing Model
The C17 covers the iPhone X, XS and XS Max only. MiJing sells separate fixtures for later generations, such as the C18 for the iPhone 11 series, the C20 for the iPhone 12 series and the C21 for the iPhone 13 series. Match the fixture to the board you service, because the C17 does not accept boards from those later models. Workshops that handle a mix of generations usually build a small fixture range and add models as their repair volume grows.
Why Mechanicpk Stocks the C17
Mechanicpk supplies mobile repair tools to technicians, repair shops and service centres across Pakistan. The C17 suits shops that repair iPhone X-series boards at component level and want a reliable pre-assembly check. It complements the reballing kits, test boxes and PCB holders in the same catalogue, so you can equip one bench from a single order.
| Weight | 0.25 kg |
|---|
Key Features
- ✓3-in-1 fixture covering iPhone X, XS and XS Max boards
- ✓Layered design with lower board, pin board and upper board in one rack
- ✓Middle-layer function testing outside the chassis
- ✓First connection method for screen cable, boot, power cord or battery testing
- ✓Second connection method with base end plug for flashing
- ✓Cuts repeated teardown and the solder joint damage that follows
- ✓Covered test rack for stable board placement
- ✓Fits board-level repair benches alongside multimeters, microscopes and PCB holders
Specifications
| Brand | MiJing |
|---|---|
| Model | C17 |
| Category | Motherboard Layered Test Fixture |
| Compatibility | iPhone X, iPhone XS, iPhone XS Max |
| Supported Devices | iPhone X, iPhone XS, iPhone XS Max |
| Technology | 3-in-1 layered middle-layer function testing |
Common Repair Uses
- ✓Board-level function testing for iPhone X-series repair
- ✓Function testing a two-layer board before middle frame assembly
- ✓Checking screen response during board testing
- ✓Confirming boot behaviour after IC replacement or reballing
- ✓Testing power on/off response with the power cable
- ✓Testing with a battery or power cord connected
- ✓Flashing a board through the base end plug connection
- ✓Isolating board faults from screen or battery faults on dead phone cases
- ✓Re-checking boards after rework to avoid repeated disassembly
Compatible Devices
- ✓iPhone X, iPhone XS and iPhone XS Max logic boards only
- ✓iPhone X logic board (lower and upper layers)
- ✓iPhone XS logic board (lower and upper layers)
- ✓iPhone XS Max logic board (lower and upper layers)
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Can the MiJing C17 test an iPhone 11 or iPhone 12 board?
What do I connect to the MiJing C17 to test a board?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



