Mijing HC-03 0.3mm Solder Wire for Mobile Repair
₨ 900
Mijing HC-03 0.3mm Solder Wire
Mijing HC-03 is a 0.3mm solder wire for mobile repair with an Sn60/Pb40 tin-lead alloy, a rosin flux and 50g net content. The alloy melts at 183°C, so your iron or hot air station reaches flow temperature fast without stressing nearby SMD components. The fine diameter gives you exact control over solder volume on charging port pads, FPC connector pads, battery connector pads and jumper points. Mijing lists low impurities, low impedance and a low-smoke rosin that cleans off easily. Repair shops and technicians across Pakistan order it from Mechanicpk for daily board-level work.
In stock
0.3mm Solder Wire for Mobile Repair: Mijing HC-03 Technical Overview
This 0.3mm solder wire for mobile repair gives technicians a fine-gauge tin-lead feed for board-level work. Mijing builds the HC-03 on an Sn60/Pb40 alloy with a rosin flux, packs 50g net per unit, and rates the melting point at 183°C. The HC-03 code marks the 0.3mm diameter inside a three-size family: the HC-05 covers 0.5mm and the HC-08 covers 0.8mm for heavier joints. If your bench handles dead phone boards, charging issue repairs and connector replacement every day, the 0.3mm size keeps solder volume under your control.
Key Technical Highlights
Fine wire matters on modern boards where pads sit close together. A 0.3mm wire lets you feed a measured amount of solder onto one pad instead of flooding the pads beside it, which cuts bridging on tight connector footprints. The Sn60/Pb40 alloy melts at 183°C, a lower flow temperature than lead-free wire, so you put less heat into the board. Lower heat protects flex connectors, plastic housings and heat-sensitive SMD parts near the joint.
Mijing lists the HC-03 with few impurities, low impedance, high conductivity, oxidation resistance and high flux activity. The rosin uses organic active chemistry, produces less smoke and cleans off easily, so the board looks tidy before you close the phone. Each unit carries 50g net, which gives a busy bench a steady supply for fine pad work.
Repair Workflow Fit
Reach for the HC-03 whenever you solder at pad level. Typical jobs include re-tinning pads after IC change karna, jumper lagana on broken tracks, rebuilding charging port and battery connector joints, and reflowing cold joints on hardware fault boards. ISP pinout tools and eMMC programmers often need fine wires soldered to test points on a dead phone board, and 0.3mm wire suits those small pads.
Pair the wire with a temperature-controlled soldering station for iron work and a hot air station when you need to lift a part first. A microscope shows you the solder volume on every pad, and a PCB holder keeps the board still while you feed the wire. Check continuity with a multimeter before you power the board. If your workflow also uses test boxes, UFS adapters or reballing kits, keep the HC-03 beside them for pad repair between steps.
Safety and Handling
Sn60/Pb40 contains lead. Work with ventilation or fume extraction, wash your hands after handling, and keep the unit away from food and children. If your customer or process requires RoHS-compliant joints, choose a lead-free wire instead.
Choosing the Right Diameter
Pick the HC-03 when your work centres on small pads, fine connectors and tight component spacing. Step up to the HC-05 or HC-08 when you solder larger pads, shield frames or thicker wire leads and need more solder per second. Many workshops stock more than one size so every joint gets the right volume of solder.
| Weight | 0.5 kg |
|---|
Key Features
- ✓0.3mm fine diameter for pad-level solder control
- ✓Sn60/Pb40 tin-lead alloy
- ✓183°C melting point
- ✓50g net content
- ✓Rosin flux with organic active chemistry
- ✓Low-smoke rosin with easy-clean residue
- ✓Few impurities, low impedance and high conductivity, as listed by Mijing
- ✓Oxidation resistance and high flux activity, as listed by Mijing
Specifications
| Brand | Mijing |
|---|---|
| Model | HC-03 |
| Category | Solder Wire |
| Compatibility | Universal — not device-specific |
| Technology | Sn60/Pb40 tin-lead solder wire with rosin flux, 183°C melting point |
| Material | Tin-lead alloy (Sn 60%, Pb 40%) with rosin flux |
| Wire Diameter | 0.3mm |
| Weight | 50g net |
Common Repair Uses
- ✓Fine pad-level hand soldering on mobile phone and PCB repair benches
- ✓Re-tinning pads after IC change karna
- ✓Jumper lagana on broken tracks
- ✓Charging port pad repair
- ✓Battery connector joint repair
- ✓FPC connector pad rebuild
- ✓Cold joint reflow on hardware fault boards
- ✓Soldering ISP and test-point wires on dead phone boards
- ✓Small SMD component replacement
Compatible Devices
- ✓Universal — not device-specific; suits any board that accepts tin-lead hand soldering
- ✓Android smartphone motherboards
- ✓iPhone logic boards
- ✓Feature phone boards
- ✓Tablet PCBs
- ✓Laptop and computer PCBs
- ✓Charging flex and connector pads
- ✓FPC and battery connector pads
- ✓General electronics PCBs



