Mechanic L1 Pro Rechargeable UV Curing Lamp
₨ 2,600
Mechanic L1 Pro UV Curing Lamp
The Mechanic L1 Pro is a rechargeable UV curing lamp for mobile repair benches. Two UV lamp beads deliver 5–7W of curing power for UV solder mask, OCA, shadowless glue, and resin. You pick a 30-second, 60-second, or continuous timer, then work hands-free while the lamp cures. The built-in battery and Type-C input let you run it cordless or from a power bank, so no cable drags across your board. An aluminum alloy body with a ventilation grille keeps heat under control during repeated cycles. The compact housing fits next to your microscope and PCB holder without crowding the bench.
In stock
Mechanic L1 Pro: A UV Curing Lamp for Mobile Repair That Cures at the Board
The Mechanic L1 Pro is a UV curing lamp for mobile repair built for the moment after a trace fix, when exposed copper needs fresh solder mask before you reassemble the phone. Mechanic packs two UV lamp beads into a compact body, so the light concentrates over the repair area instead of scattering across the bench. You cure UV solder mask, OCA, shadowless glue, and resin with one tool that charges over Type-C. A repair shop that handles dead phone boards daily gains a faster, cleaner finish on every job.
Dual-Bead Output and Timer Control
The L1 Pro runs on 5V input with a rated power of 5–7W across its two UV lamp beads. The dual-bead layout spreads the load, and the aluminum alloy housing carries heat away through its ventilation grille. That matters when you cure several boards back to back. Three timer modes let you match the job: 30 seconds for a thin solder mask patch, 60 seconds for thicker glue or resin, and continuous mode when you need the lamp on until you switch it off. You set the mode, position the lamp, and keep your hands free for the next step.
Where the Lamp Fits in Your Board-Level Workflow
Most UV curing happens at the end of a repair chain. You remove a damaged IC with your hot air station, clean the pads, reball or resolder with your soldering station, and check continuity with your multimeter. After a jumper lagana job or a trace rebuild, you seal the repair with UV solder mask and cure it under the L1 Pro. You then hold the board steady in a PCB holder and inspect the result under your microscope. The same lamp also cures UV flux paste and optical adhesive during screen and glass work, so it stays useful beyond motherboard jobs. Technicians who work on boot loop issue boards, charging issue boards, and dead after flash cases reach for it whenever a repair leaves bare copper.
Cordless Curing on a Crowded Bench
The built-in rechargeable battery lets you move the lamp freely, and the Type-C port accepts a power bank or a standard USB supply. You skip the wall socket hunt and the short cable that pulls the lamp off its mark. The compact body measures 51 × 51 × 57 mm, so it sits close to the work without blocking your microscope view. When your bench handles BGA rework, reballing kit sessions, and CPU repair in the same shift, a small cordless lamp keeps the workflow moving instead of waiting on a fixed curing station.
Why Repair Shops Add It to the Tool Bench
A reliable UV curing lamp for mobile repair cuts rework. Cured solder mask protects exposed traces from shorts and from handling damage, which protects your repair warranty. You also reduce the time each board spends on the bench, since you no longer wait for slow ambient curing. For shop owners, one lamp per technician keeps every station independent, and the Type-C charging standard means your existing chargers and power banks already work.
| Weight | 0.10 kg |
|---|
Key Features
- ✓Dual UV lamp bead design
- ✓5–7W rated power
- ✓Built-in rechargeable battery
- ✓Type-C 5V power input
- ✓30-second, 60-second, and continuous timer modes
- ✓Aluminum alloy body with ventilation grille
- ✓Compact 51 × 51 × 57 mm size
- ✓Runs from a power bank for cordless use
Specifications
| Brand | Mechanic |
|---|---|
| Model | L1 Pro |
| Category | UV Curing Lamp |
| Compatibility | Universal — not device-specific |
| Technology | Dual UV LED lamp beads |
| Material | Aluminum alloy |
| Input Voltage | 5V (Type-C) |
| Power Rating | 5–7W |
| Dimensions | 51 × 51 × 57 mm |
Common Repair Uses
- ✓Board-level curing and adhesive work in mobile and PCB repair
- ✓Curing UV solder mask after trace repair
- ✓Sealing jumper wire repairs on dead phone boards
- ✓Curing solder mask after IC change karna
- ✓Protecting exposed copper after pad repair
- ✓Bonding with shadowless UV glue
- ✓Curing OCA optical adhesive
- ✓Curing UV resin glue
- ✓Drying UV flux paste after BGA and CPU rework
Compatible Devices
- ✓Universal curing tool — works on any board or part coated with UV-curable material; not tied to specific phone models or chipsets
- ✓Mobile phone motherboards (all brands)
- ✓Laptop motherboards
- ✓CPU and BGA chip repair areas
- ✓UV solder mask coated PCB traces
- ✓OCA optical adhesive joints
- ✓Shadowless (UV) glue applications
- ✓UV curable resin glue
- ✓UV flux paste
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which timer modes does the Mechanic L1 Pro offer?
Can I power the Mechanic L1 Pro from a power bank?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
Qianli 011 16-in-1 Glue Removal Knife for Mobile Repair
Out of stock
RELIFE RL-004SA silicone pad – Anti-slip
In stock



