KADA 850/852 Heat Gun Handle Pipe 5 Wire
₨ 1
KADA Hot Air Gun Handle, 5 Wire
The KADA 852 heat gun handle replaces a dead or burnt handpiece on KADA 850 and 852-series hot air rework stations. You get a 5-wire cable, an internal heating element with temperature sensing, and a heat-resistant body built for long board-level sessions. Swap it in when your station powers on but the handle stops heating, blows weak, or drops out mid-reflow. Mechanicpk supplies it as a standalone spare, so you restore hot air function without buying a complete station. Match the 5-wire connector to your station before you order, then use the handle for IC removal, SMD rework, and motherboard repair on your bench.
Out of stock
KADA 852 Heat Gun Handle for 850/852 Hot Air Rework Stations
The KADA 852 heat gun handle is a replacement hot air handpiece for KADA 850 and 852-series rework stations, and this version uses a 5-wire cable. When your station boots, the controller reads normally, and the handle still delivers no heat or unstable airflow, the handle assembly usually holds the fault. Replacing the handle costs far less than a new station and restores hot air in minutes. Mechanicpk stocks this spare for Pakistani repair shops that run hot air stations daily on mobile logic boards.
Handle Construction and Technical Highlights
The handle integrates a heating element and a temperature sensor inside a heat-resistant plastic and metal body. Distributor data lists a working ceiling of roughly 450°C, a handle length of about 18 to 20 cm, and a cable of about 70 cm. The cable carries heater power and sensor feedback between the handle and the station, so the controller can regulate temperature while you work. The handle accepts interchangeable nozzles, which lets you match airflow to the component size, from a small IC to a shield can. The compact body keeps the weight low, so your wrist stays steady during long reflow passes.
Where the Handle Fits in Your Rework Workflow
Hot air sits at the center of board-level repair. You use it for IC change karna on a dead phone, shield removal, connector replacement, and BGA reflow before or after reballing. A weak or intermittent handle turns each of those jobs into guesswork, and a hardware fault you could fix in one pass becomes a lifted pad or a cooked neighboring component. A stable handle gives you repeatable heat, which matters more than raw temperature.
Pair the handle with a preheater or PCB holder to hold the board flat, and put a microscope over the joint so you watch the solder flow instead of guessing. Keep your reballing kit and flux nearby, and run a multimeter across the board after rework to confirm no short remains on the charging or power rail. If you also run a soldering station for through-hole and pad cleanup, the hot air handle covers everything the iron cannot reach.
Choosing and Fitting the Right Handle
Before you order, check your station’s handle connector and count the wires on the old cable. Hot air handles come in 4-wire, 5-wire, and 6-wire layouts, and a different layout will not plug in correctly. This listing covers the 5-wire version sold for KADA 850, 852D+, and 858D+ class stations. Open the old handle and test the cable with a multimeter for continuity first. A broken cable wire looks identical to a dead heating element from the outside, and you want to know which one you are replacing.
If your station is old and the handle is the third part you have replaced, compare the cost of continued repairs against an upgrade to a newer hot air station. For a station that otherwise runs well, this handle gives you the fastest and cheapest way back to full production on your repair bench.
| Weight | 0.4 kg |
|---|
Key Features
- ✓5-wire cable replacement handle for KADA hot air rework stations
- ✓Integrated heating element and temperature sensor
- ✓Working temperature up to approx. 450°C
- ✓Heat-resistant plastic and metal body
- ✓Cable length of approx. 70 cm for free movement across the bench
- ✓Supports interchangeable nozzles
- ✓Restores hot air function without replacing the full station
- ✓Suits daily use in mobile repair shops and service centers
Specifications
| Brand | KADA |
|---|---|
| Model | KADA 850/852 Heat Gun Handle Pipe 5 Wire |
| Category | Hot Air Gun Handle / Hot Air Station Spare Part |
| Compatibility | KADA 850 / 852D+ / 858D+ hot air rework stations |
| Technology | Internal heating element with temperature sensor, 5-wire cable |
| Material | Heat-resistant plastic and metal |
| Input Voltage | 220V AC (supplied through the station) |
| Cable Length | Approx. 70 cm |
| Handle Length | Approx. 18–20 cm |
| Maximum Temperature | Up to approx. 450°C |
Common Repair Uses
- ✓Hot air rework on mobile phone boards and general electronics.
- ✓IC removal and replacement on dead phone boards
- ✓SMD component desoldering and soldering
- ✓Shield can and connector removal
- ✓BGA reflow before and after reballing
- ✓Mobile phone motherboard repair
- ✓PCB repair and maintenance
- ✓Heat shrink tubing work
- ✓Replacing a faulty handle that stopped heating
Compatible Devices
- ✓Station-level compatibility (not phone-model specific). Works on any phone board a compatible KADA hot air station can rework.
- ✓KADA 850 hot air rework station
- ✓KADA 852 hot air rework station
- ✓KADA 852D+ hot air rework station
- ✓KADA 858D+ hot air rework station
- ✓Similar KADA-family stations that use the same 5-wire handle connector
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Does a 5-wire handle fit every KADA hot air station?
What temperature can this heat gun handle reach?
Related products
ICFRIEND UFS eMMC ISP Adapter for MiPi Tester & F64 Box
In stock
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock



