Mechanic 900M-T-TI Lead-Free Solder Tip for 936 Stations
₨ 1
900M-T-TI Lead-Free Soldering Tip
The Mechanic 900M-T-TI soldering tip gives your 936-class station a lead-free replacement tip with a red copper substrate and iron and nickel plating. It fits 936, 937, 938, 969, 8586 and 852D stations, works across a 200–480°C range, and covers the daily jobs on a phone motherboard: desoldering, drag soldering, glue removal, pad cleaning and reflow. Check that your iron uses the 900M-T interface before you order, because 900M-T series tips do not fit 908 or 900S-type irons. Add it to your repair bench and keep a spare for busy weeks.
Out of stock
900M-T-TI Soldering Tip for Lead-Free Board Repair
The Mechanic 900M-T-TI soldering tip belongs to the 900M-T lead-free series that fits the 936-class stations on most Pakistani repair benches. It combines a red copper substrate with iron and nickel plating, so heat reaches the pad quickly and the tip resists oxidation between jobs. If you work with lead-free alloy on phone motherboards, this tip keeps your station matched to that workflow. You swap it into your existing handle, set your temperature and return to the board without changing your setup.
Heat Transfer and Plating Construction
Red copper moves heat from the heating element to the contact surface fast, and that speed decides how long a joint stays under heat. The iron plating protects the copper from erosion, and the nickel layer adds corrosion resistance. Lead-free alloys run hotter and attack bare copper quickly, so a plated tip lasts longer on a busy bench. The tip suits stations that operate between 200°C and 480°C, which covers routine soldering and rework on mobile PCBs. The 4mm inner bore slides over the heating element of a 900M-T handle. Keep the tip tinned between joints, because a dry tip oxidises and stops transferring heat.
Repair Workflow Fit for the 900M-T-TI Soldering Tip
Mechanic sells its Master Series tips for motherboard repair: desoldering, drag soldering, glue removal, pad cleaning and reflowing. On a dead phone that needs jumper lagana after a burnt track, you tin the wire end, lay the jumper and flow the joint with this tip. On a charging issue or other hardware fault, you clean the leftover solder from the pads after an IC change, re-tin them and place the next component. Pair the tip with a hot air station for lifting ICs, a microscope for checking joints and a PCB holder that keeps the board steady under your hand.
Why Technicians Stay With the 900M-T Interface
The 900M-T standard is common, so you find spare tips and matching stations easily. When you move between tip styles, you keep the same handle, controller and temperature setting. Shops that run several benches stock one tip family and swap tips between jobs instead of buying a new iron. After you solder, check continuity with a multimeter before you power the board. When a repair calls for BGA work, move to your reballing kit and hot air station, and use this tip for the pads, jumpers and small components around the chip.
Check Your Handle Before You Order
Confirm that your iron accepts 900M-T tips. This tip family fits 936, 937, 938, 969, 8586 and 852D stations, and it does not fit 908 or 900S-type irons. Buy at least one spare, since a tip that sees daily lead-free work wears out sooner than the iron that holds it. Store spares dry, and clean the tip on a brass sponge or wet sponge according to your station’s guidance.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Lead-free 900M-T series construction
- ✓Red copper substrate for fast heat transfer
- ✓Iron plating that protects the copper
- ✓Nickel layer for corrosion resistance
- ✓200–480°C working range
- ✓4mm inner diameter for 900M-T handles
- ✓Fits 936, 937, 938, 969, 8586 and 852D stations
- ✓Suited to motherboard desoldering, drag soldering and pad cleaning
Specifications
| Brand | Mechanic |
|---|---|
| Model | 900M-T-TI |
| Category | Soldering Iron Tip |
| Compatibility | 936, 937, 938, 969, 8586 and 852D soldering stations |
| Technology | Lead-free 900M-T series, Master Series |
| Material | Red copper substrate with iron and nickel plating |
| Temperature Range | 200–480°C |
| Inner Diameter | 4mm |
Common Repair Uses
- ✓Board-level soldering and desoldering on mobile phone motherboards
- ✓Desoldering components
- ✓Drag soldering
- ✓Removing glue from boards
- ✓Cleaning pads after IC removal
- ✓Reflowing small joints
- ✓Jumper wire soldering on burnt tracks
- ✓Tinning pads and wire ends
- ✓General motherboard maintenance on a repair bench
Compatible Devices
- ✓900M-T-interface soldering stations (station compatibility, not phone-specific)
- ✓Hakko-style 936 soldering station
- ✓937 soldering station
- ✓938 soldering station
- ✓969 soldering station
- ✓8586 rework station
- ✓852D rework station
- ✓907 soldering station
- ✓Other 900M-T-interface stations from brands such as Quick, Aoyue, Yihua and Atten
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Which soldering stations accept the 900M-T-TI tip, and which irons does it not fit?
What temperature range does the 900M-T-TI tip support?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock



