YCS-N01 Deglue Knife Glue Removal Blade
₨ 300
YCS N01 Glue Removal Blade
The YCS N01 glue removal blade clears hardened black adhesive from mobile phone and tablet motherboards. It also cleans the area around CPU and BGA chips before you start rework. You scrape the glue away without damaging the circuit board. The blade keeps a sharp edge through repeated use, so every glue job starts with a clean cut. Pair it with your hot air station, microscope, and PCB holder for precise board-level work. Mechanicpk supplies the YCS-N01 deglue knife to Pakistani repair shops, service centers, and technicians who want a dedicated glue blade on the bench.
In stock
YCS-N01 Glue Removal Blade for Board-Level Repair
The YCS N01 glue removal blade does one job on your repair bench: it lifts black adhesive off a motherboard before you touch the chip underneath. A dead phone with a hardware fault around the CPU or a BGA chip often arrives with hardened glue that blocks hot air, hides pads, and makes IC change karna risky. This deglue knife gives you a dedicated edge for that glue, so you stop forcing a general-purpose knife or screwdriver tip into tight board areas.
Where the N01 Fits in Your Rework Sequence
Board-level repair follows a predictable order, and glue removal sits near the start. You open the phone, pull the shields, and inspect the area around the CPU, memory chip, or charging IC. Black glue often seals the edges and corners of these chips. If you skip it, hot air heats the adhesive unevenly, the chip resists lifting, and you risk tearing pads. With the N01, you cut and scrape that glue first, then move to your hot air station and pry tool.
The same step matters after the chip comes off. You clear leftover glue from the pad area before reballing, so your stencil sits flat and your new balls land clean. Under a microscope, a dedicated glue blade lets you follow the adhesive line and remove it in small, controlled passes.
Blade Behavior on Mobile and Tablet Motherboards
YCS builds the N01 to remove black adhesive without damaging the circuit board. The sharp blade holds its edge over extended use, so you do not stop mid-job to swap a dull tool. You use the same blade on mobile phone and tablet motherboards, around CPU and BGA chip positions.
Technique protects the board. Keep the blade low, push in short strokes away from neighboring components, and stop as soon as the glue lifts. On stubborn spots, apply gentle heat from your soldering station or hot air gun, and rest the board in a PCB holder so it stays still while you work. This method protects the solder mask and small SMD parts on dense boards, where one slip creates a second hardware fault on top of the first.
Choosing the N01 or the N02 for the Job
YCS sells the N01 and N02 side by side, and each serves a different step. The N01 handles glue removal. The N02 targets CPU and IC chip removal with a sharp, non-deforming blade built for prying components. Most benches use both: the N01 clears the adhesive first, then the N02 lifts the chip once the glue no longer holds it down.
If your daily work includes charging IC, CPU, or memory chip jobs, stock both blades and add a reballing kit, a microscope, and a soldering station to complete the workflow. If you only clean glue off boards, the N01 covers that task alone. Mechanicpk stocks the YCS-N01 for repair shops, service centers, and technicians across Pakistan who want a dedicated glue blade ready on the bench.
| Weight | 0.1 kg |
|---|
Key Features
- ✓Dedicated blade for black adhesive removal on motherboards
- ✓Removes glue without damaging the circuit board
- ✓Sharp edge that holds up through extended use
- ✓Suits mobile phone and tablet motherboards
- ✓Works around CPU and BGA chip positions
- ✓Fits the glue-first step of the rework sequence
- ✓Pairs with the YCS N02 CPU removal blade
- ✓Works with microscope-assisted board cleaning
Specifications
| Brand Entity | YCS |
|---|---|
| Product Entity | YCS-N01 Deglue Knife Glue Removal Blade |
| Technology Entity | Black adhesive removal blade for PCB rework |
| Compatible Device Entities | Mobile phone motherboards, tablet motherboards, CPU chips, BGA chips |
| Repair Process Entity | Glue removal before chip removal and reballing |
| Industry Entity | Mobile phone repair, board-level PCB repair |
Common Repair Uses
- ✓Black glue removal and board cleaning during CPU, IC, and BGA rework
- ✓Black glue removal around CPU chips
- ✓Glue clearing around BGA chip edges
- ✓Glue scraping before IC change karna
- ✓Pad area cleaning before reballing
- ✓Motherboard glue cleaning on dead phone repair
- ✓Prep before hot air chip removal
- ✓Glue cleanup on tablet motherboards
- ✓Residue removal after chip lift
Compatible Devices
- ✓Universal scope, covers glue on mobile phone and tablet motherboards (not device-specific)
- ✓Mobile phone motherboards
- ✓Tablet motherboards
- ✓Areas around CPU chips
- ✓Areas around BGA chips
- ✓Areas around IC chips
- ✓Android board-level repair work
- ✓iPhone board-level repair work
- ✓General PCB glue cleaning
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
What is the difference between the YCS N01 and the YCS N02?
Can I use the YCS N01 to clear glue before reballing a CPU or BGA chip?
Related products
JZQ-599B Soldering Iron Tip Cleaner with Tin Cleaning Ball
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



