2UUL FX-002S 0.02MM Ultrasoft CPU Jumper Wire 100m

₨ 800

0.02mm CPU Jumper Wire for Pad Repair

The 2UUL FX-002S 0.02MM Ultrasoft CPU Jumper gives your repair bench a 100m spool of ultra-fine, uninsulated silver-plated copper wire for micro soldering. At 0.02mm, it rebuilds torn CPU and BGA pads, bridges broken traces, and restores fingerprint sensor connections on dead phone boards without crowding neighbouring joints. The ultrasoft build bends into tight routes under a microscope, and the non-magnetic wire stays tough enough to resist snapping mid-repair. Mechanicpk supplies this universal jumper wire to technicians, repair shops, and service centers across Pakistan that run board-level work every day.

In stock

13 People watching this product now!
Description

Why a 0.02mm CPU Jumper Wire Belongs on Your Bench

The 2UUL FX-002S 0.02MM Ultrasoft CPU Jumper is a 100-metre spool of 0.02mm CPU jumper wire made for one job: rebuilding the connection when a BGA pad or trace lifts off the board. At 0.02mm, the wire fits between tightly spaced joints, so you can route a repair without touching the neighbouring pads. 2UUL lists the FX-002S as the ultrasoft version of its 0.02mm line, and the 100m length gives your bench a long-lasting supply of flying wire. If your shop sees dead phone boards with torn CPU pads after a failed reball, or fingerprint sensor connections that need rebuilding, this is the consumable you reach for first. The sections below cover the wire’s construction, its place in your repair workflow, and what to check before you buy.

Silver-Plated Copper, Uninsulated, Built to Bend

The FX-002S uses silver-plated copper at a 0.02mm diameter. Distributor listings describe it as uninsulated, so the bare surface takes solder directly and carries current from the first millimetre. The same listings call it non-magnetic, tough, and free of breakpoints along the spool, which matters when you pull a metre of hair-thin wire off the reel and bend it around a pad under magnification. The ultrasoft build lets you shape tight corners and follow a trace route without fighting the wire. Diameter decides what you can repair. A thicker jumper bridges a lifted pad but crowds the next row of balls, while 0.02mm keeps the joint profile small, so the chip sits closer to the board when you reflow it. Because the wire carries no insulation, you keep it clear of adjacent pads and trim it short with a sharp blade before you tin.

Where the Jumper Fits in Your Repair Workflow

You reach for this wire after the damage is already done. A failed reball, a hot air session that lifts a pad, or a dead phone that shows no CPU contact under the microscope all lead to the same step. Clean the area with flux, expose the broken trace or pad edge, tin the exposed end, and run the 0.02mm wire from the lifted pad to the nearest live point. Check continuity with a multimeter before you place the chip, because a dead jumper under a BGA costs you a full reball to fix. The same method restores fingerprint sensor connections and bridges broken tracks near BGA chips on boards that arrive with a charging issue or display problem. A stable microscope, a temperature-controlled soldering station, a hot air station, and a PCB holder complete the setup, and a reballing kit covers the chip once the pad is fixed.

Buying Notes for Repair Shops and Service Centers

A 100m spool is a shop-level quantity, so one reel serves a busy technician for a long stretch. Distributors list the FX-002S as universal rather than device-specific, so it suits any board that needs a 0.02mm jumper. 2UUL sells related sizes in the same line, including the FX-002 non-insulated wire, the FX-002A insulated 0.02mm wire, and finer 0.01mm (FX-001) and 0.009mm (FX-0009) options. If your boards use tighter pad spacing, step down to the finer sizes. If your repair needs built-in insulation, the FX-002A covers it. Keep a spool beside your flux, solder, and tweezers, and you handle pad repairs at the bench without sending the board away.

Additional information
Weight0.20 kg
Q & A
Please login to post questions

Key Features

  • 0.02mm ultra-fine wire diameter for micro soldering on tightly spaced pads
  • Ultrasoft build that bends into tight routes under a microscope
  • Silver-plated copper material
  • Uninsulated surface that takes solder directly
  • Non-magnetic wire
  • Tough wire with no breakpoints along the spool
  • 100m spool for long-term use across many repairs
  • Universal use, not tied to a single phone brand or model

Specifications

Brand Entity2UUL
Product Entity2UUL FX-002S 0.02MM Ultrasoft CPU Jumper Wire, 100m spool
Technology Entity0.02mm silver-plated copper jumper wire, uninsulated flying wire
Compatible Device EntitiesSmartphone logic boards, CPU BGA pads, fingerprint sensor connections, motherboard traces
Repair Process EntityCPU pad restoration, BGA pad repair, micro soldering, trace bridging
Industry EntityMobile repair industry, PCB repair, soldering and rework

Common Repair Uses

  • Restoring lifted or peeled CPU pads after reballing
  • Repairing BGA chip pads
  • Bridging broken PCB traces with flying wire
  • Rebuilding fingerprint sensor connections
  • Micro soldering on dead phone boards
  • Fixing charging issue boards with damaged pads near ICs
  • Repairing display problem boards with broken connection points
  • Pad and trace repair on small-electronics motherboards

Compatible Devices

  • Universal use, not device-specific. Suits any board that needs a 0.02mm jumper.
  • Smartphone logic boards with BGA CPU pads
  • Android phone motherboards
  • iPhone logic boards
  • Motherboard fingerprint sensor connections
  • BGA chip pads on eMMC, UFS, and IC packages
  • Torn or lifted CPU solder joints
  • Broken traces near BGA chips
  • Tablet and other small-electronics PCBs

FAQ

What is the product name?
The product name is 2UUL FX-002S 0.02MM Ultrasoft CPU Jumper Wire 100m.
What is the brand of this product?
The brand of this product is 2UUL.
What is the model of this product?
The model of this product is FX-002S.
What is this product used for?
This product is used for repairing lifted CPU and BGA pads, bridging broken traces, and micro soldering on mobile phone motherboards.
Which devices are compatible with this product?
This product is universal. It works on any board that needs a 0.02mm jumper and is not limited to specific phone models.
Who should use this product?
This product is suitable for mobile repair technicians, repair shops, service centers, and professional users.
Is the 2UUL FX-002S jumper wire insulated?
No. Distributor listings describe the FX-002S as uninsulated silver-plated copper wire, so you keep it clear of neighbouring pads. For an insulated 0.02mm option, 2UUL offers the FX-002A.
What diameter and length does the FX-002S come in?
The FX-002S has a 0.02mm wire diameter and comes on a 100m spool.