2UUL SC61 Ultra Clean Soldering Rosin Flux for PCB
₨ 750
SC61 Ultra Clean Rosin Flux Paste
The 2UUL SC61 rosin flux gives your bench an ultra clean, low-residue paste for PCB repair and rework. It supports SMD and BGA soldering, so you can handle IC change karna jobs, reballing prep, and pad repair on smartphone mainboards without fighting heavy residue. The formula carries a mild pH and does not corrode ICs or PCB, and the transparent residue needs no washing. Mechanicpk supplies the 2UUL SC61 to repair shops and service centers across Pakistan that need predictable flux behaviour at board level. Pair it with your hot air station, soldering station, and reballing kit for a complete rework setup.
In stock
2UUL SC61 Rosin Flux: Ultra Clean Soldering Rosin for SMD and BGA Rework
The 2UUL SC61 rosin flux belongs on any bench that handles SMD and BGA rework every day. This ultra clean soldering rosin comes as a flux paste built for PCB repair, which makes it a direct fit for smartphone mainboards where tight pad spacing leaves no room for messy residue. Mechanicpk supplies the 2UUL SC61 to technicians who want one consistent flux for IC change karna jobs, pad rebuilds, and reflow work. The paste keeps residue low and supports strong electrical conductivity, so your joints stay clean and your boards look professional when they go back to the customer. Pakistani repair shops that push boards through reflow every day need a flux that behaves the same way on the first board and the fiftieth.
Low-Residue Chemistry for Board-Level Work
Flux has one job at the joint: it strips oxide from copper pads and component terminals so solder wets properly. The SC61 formula carries a mild pH, and the supplier information lists it as non-corrosive to ICs and PCB. That matters on dense phone boards, where an aggressive flux trapped under a BGA package damages pads long after the repair. The residue turns transparent after heating, and the product information says it needs no washing. You can still wipe the area with IPA when a customer expects a spotless finish, but routine jobs skip the mandatory wash step and save bench time. Low residue also keeps your microscope view clear, because you inspect the real solder fillet instead of a brown film.
Where SC61 Fits in Your Rework Workflow
Apply a thin layer of flux on the pads before you place a component. Keep the amount small: a thin, even coat wets the pads fully, while excess paste only leaves extra residue around neighbouring components. For reballing, spread the paste across the cleaned pads, set the balls with your stencil, and bring the area to temperature with your hot air station. For small SMD parts around the charging section, drop a little flux on the pads, tin them with your soldering station, and place the part. Flux sits inside nearly every step of a hardware fault repair: lifting the suspect IC, cleaning the pads, and refitting the new one. A charging issue, a display problem, or a dead phone that traces back to a damaged line all end up on the same flux-assisted workflow.
Jumper lagana on a broken track also goes faster when flux lets solder wet the bare copper on contact. Pair the paste with a PCB holder to keep the board steady, a multimeter to confirm the repaired line, and a microscope to check the finished joints. Technicians who solder test points and thin wires for ISP pinout, eMMC, or UFS adapter work use the same flux to keep those small connections clean and bright.
Buying Notes for Pakistani Repair Shops
Treat flux as a consumable you restock, not a one-time tool. A shop that reballs several boards a day burns through paste faster than a bench that handles an occasional charging port job, so size your order to your weekly board count. Consistency matters more than novelty here. Switching flux mid-repair changes how solder flows and how residue behaves, and that variable costs you time on fine-pitch work. Standardise on one flux across every bench so each technician gets the same result.
If your rework chain still runs on basic equipment, upgrade the surrounding setup alongside the flux. Better hot air stations, steadier soldering stations, and proper reballing kits all raise the ceiling on what clean flux can deliver. The SC61 gives you the chemistry side of that chain at the board level, and Mechanicpk stocks the rest of the bench so you can build the full setup in one order.
| Weight | 0.9 kg |
|---|
Key Features
- ✓Ultra clean, low-residue rosin flux formula
- ✓Paste form for controlled, precise application
- ✓Mild pH, listed as non-corrosive to ICs and PCB
- ✓Transparent residue, no washing needed
- ✓Supports high electrical conductivity at the joint
- ✓Compatible with SMD and BGA soldering
- ✓Built for PCB repair and rework
- ✓Suits smartphone, PCB, and electronic parts repair
Specifications
| Brand | 2UUL |
|---|---|
| Model | SC61 Ultra Clean Flux |
| Category | Soldering Flux & Rosin |
| Compatibility | SMD and BGA soldering |
| Technology | Rosin-based flux paste, low residue, mild pH |
| Material | Rosin flux paste |
Common Repair Uses
- ✓Flux-assisted SMD and BGA soldering during PCB repair and rework
- ✓IC change karna on phone mainboards
- ✓BGA reballing and reflow
- ✓SMD component replacement
- ✓Pad tinning and pad rebuilding
- ✓Jumper lagana on broken tracks
- ✓Charging issue and hardware fault repair
- ✓Display problem board-level repair
- ✓Re-soldering test points and thin wires
Compatible Devices
- ✓Universal — not device-specific; suits smartphone and other PCB assemblies with SMD and BGA components
- ✓Smartphone mainboards (any brand, universal use)
- ✓Other PCB assemblies and electronic circuit boards
- ✓BGA ICs and BGA packages
- ✓SMD ICs
- ✓SMD passive components (capacitors, resistors)
- ✓Charging section components on phone boards
- ✓Pads and tracks needing re-tinning
- ✓Electronic parts repair in general
FAQ
What is the product name?
What is the brand of this product?
What is the model of this product?
What is this product used for?
Which devices are compatible with this product?
Who should use this product?
Is the 2UUL SC61 flux compatible with BGA reballing?
Does 2UUL SC61 flux need washing after soldering?
Related products
QIANLI 008 Cutting Knife Blade for BGA Underfill Removal
Out of stock
UFI eMMC BGA Soldering Adapter (8 Footprints) for UFI-Box
In stock



